|
01-03-2016, 01:31 PM
|
|
|
|
11 posts, read 84,924 times
Reputation: 21
|
|
|
I have the setup shown in the image above. I've found the instructions for it here:
http://13kwbe213cjc2d2um30c7za9.wpen...codedodger.pdf
I have attempted this a number of times and it is not working. I can not get it to go into the programming mode. The light flashes when I open the cover, but when I do the part where you press 3, 5, 7, PROG the light does not start blinking like it's supposed to.
Does anyone have experience with these pieces of junk? |
|
01-04-2016, 12:42 AM
|
|
|
|
Location: Out there somewhere...a traveling man.
42,263 posts, read 55,644,735 times
Reputation: 119386
|
|
|
Have you pulled the cover all the way up til it clicks in place then start the programming?
|
|
01-04-2016, 06:33 AM
|
|
|
|
Location: Looking over your shoulder
31,304 posts, read 30,712,820 times
Reputation: 84410
|
|
Quote:
I have attempted this a number of times and it is not working. I can not get it to go into the programming mode. The light flashes when I open the cover, but when I do the part where you press 3, 5, 7, PROG the light does not start blinking like it's supposed to.
Does anyone have experience with these pieces of junk?
|
I don’t know if this unit is battery powered or not, if it is ~ did you change the battery? Sometimes a low or dead battery will cause problems……. |
|
01-04-2016, 08:31 AM
|
|
|
|
2,600 posts, read 7,762,212 times
Reputation: 2473
|
|
When you press 3,5,7 and program together the light will blink if you have a fresh battery and the slider is fully in the up position, but if you don't know you PIN # then you wont be able to program it.
If you think that you have all of the above correct then read the below site.
CodeDodger Compatible Garage Door Opener Parts - Programming Instructions |
|
01-04-2016, 10:22 PM
|
|
|
|
11 posts, read 84,924 times
Reputation: 21
|
|
Quote:
Originally Posted by need4speed2012
|
Pressing 8 and PROG together is supposed to clear the old PIN I thought. I have been doing that first, then trying the 357PROG. I can't get the blinking to start! |
|
01-04-2016, 10:45 PM
|
|
|
|
Location: Out there somewhere...a traveling man.
42,263 posts, read 55,644,735 times
Reputation: 119386
|
|
|
If you have tried all the above and still fail then get a ladder and on your overhead garage unit press the red reset button and hold it for about 6 secs. The try re-coding the opener again.
If that doesn't work and nothing else works then contact a garage door company for assistance.
|
|
10-10-2018, 08:34 AM
|
|
|
|
1 posts, read 4,446 times
Reputation: 15
|
|
|
There is a tab on the cover that pushes the top left hand button in when the cover is open. The cover MUST be on the keypad and the tab must be directly over the button so that it can constantly depress the button. Once i figured that out, the programming worked perfectly.
|
Please register to post and access all features of our very popular forum. It is free and quick. Over $68,000 in prizes has already been given out to active posters on our forum. Additional giveaways are planned.
Detailed information about all U.S. cities, counties, and zip codes on our site: City-data.com.
|
|
Please register to participate in our discussions with 2 million other members - it's free and quick! Some forums can only be seen by registered members. After you create your account, you'll be able to customize options and access all our 15,000 new posts/day with fewer ads.
