Please register to participate in our discussions with 2 million other members - it's free and quick! Some forums can only be seen by registered members. After you create your account, you'll be able to customize options and access all our 15,000 new posts/day with fewer ads.
You keep on stating Voltage but you are not stating what the Amperage is at the outlet. Low Amperage signifies a open circuit (not short circuit). Disconnect everything on the same line and try the outlet by itself. If it functions then the problem is somewhere else and you may have to replace the entire line. Shut off the breaker to that line as wherever the open circuit is may lead to a fire.
How do you measure the AMPERAGE if the device plugged into the outlet DOES NOT WORK ? There is no current flow . No current flow means NO AMPERAGE .
Is your voltmeter a "True RMS" meter? I once checked a wire under a workbench in the hangar with my Fluke 73 Multimeter, and found it had 440 volts. When the electrician came around to do some remodeling, he showed me that the wire was not connected to anything in the breaker box. It had enough induced voltage to register on the voltmeter, but it actually had no current capability.
It is obvious you have a similar situation. There is enough voltage to be read on the meter, but no current to actually do any work.
I can only recommend getting a competent electrician in to investigate.
How do you measure the AMPERAGE if the device plugged into the outlet DOES NOT WORK ? There is no current flow . No current flow means NO AMPERAGE .
What do you do for a living ?
Maybe you should read from the beginning of the thread as his meter does work in the outlet and it reading 123.4 volts which is from a device with a very small load. I'll assume either you failed Physics or have no clue how to calculate voltage. So either there is a problem with the Amperage or a problem with Resistance.
There was not an outlet in this location. Only two wires, clipped, with wire nuts on them. I installed two outlets, thinking the first was bad. The only switch controlling the power to these wires is the breaker in the panel. And I've tried both 2 and 3 pronged items. Same issue.
Try going in reverse. With the breaker switched to OFF, what no longer functions?
Maybe you should read from the beginning of the thread as his meter does work in the outlet and it reading 123.4 volts which is from a device with a very small load. I'll assume either you failed Physics or have no clue how to calculate voltage. So either there is a problem with the Amperage or a problem with Resistance.
Maybe you should read from the beginning of the thread as his meter does work in the outlet and it reading 123.4 volts which is from a device with a very small load. I'll assume either you failed Physics or have no clue how to calculate voltage. So either there is a problem with the Amperage or a problem with Resistance.
You just continue to get more confusing . What do you mean " have no clue how to calculate voltage " ? His meter is doing that for him . You don't need CURRENT to have a voltage present . And since nothing works in that outlet , THERE IS NO CURRENT . And without current , you can't " calculate voltage " based strictly on the resistance . Ever heard of Ohm's Law ?
You just continue to get more confusing . What do you mean " have no clue how to calculate voltage " ? His meter is doing that for him . You don't need CURRENT to have a voltage present . And since nothing works in that outlet , THERE IS NO CURRENT . And without current , you can't " calculate voltage " based strictly on the resistance .
Electrician would check neutral connections first. Toning out the circuit and checking for a loose neutral (commonly the white wire) would make the most sense. Most home owners won't have a toner, so he can isolate the circuit by turning the breaker off and identifying what turned off and checking the connections within the box, and leading away from that box first.
This can still be dangerous as depending on the age of the house, multiple circuits may be using the neutral as a return path so there could still be current present from other sources so much care should be taken when
Somebody had an issue before, as the OP said, the wires were just nutted off in the box. If it's an older house, this could lead to crawling in an attic, or under the house to find out where the other end is. I definitely suspect an open circuit.
Ok sport , let's try this another way . You plug in a fan to his circuit . It doesn't run . How much current is flowing through that circuit ? You yourself stated that there may be a problem with his amperage . Yeah , there is none . But that isn't the problem , it's the result .
Please register to post and access all features of our very popular forum. It is free and quick. Over $68,000 in prizes has already been given out to active posters on our forum. Additional giveaways are planned.
Detailed information about all U.S. cities, counties, and zip codes on our site: City-data.com.