- Contamination from Hands/Preventing Contamination by Employees
Observation: Food employee preparing ready to eat sandwiches with bare hands.
Correction: Except when washing fruits and vegetables as specified under 3-302.15 or as specified in paragraph D of this section, food employees may not contact exposed, ready-to-eat food with their bare hands and shall use suitable utensils such as deli tissue, spatulas, tongs, single-use gloves, or dispensing equipment.
- Wiping Cloths, Use Limitation
Observation: Cloths in-use for wiping counters and other equipment surfaces are not held between uses in a chemical sanitizer solution of proper concentration
Correction: and/or not laundered daily.
- Food Storage/Preventing Contamination from the Premises (repeated violation)
Observation: Food stored on the basement floor, (bag of onions).
Correction: Food shall be protected from contamination by storing the food: (1) In a clean, dry location
- Manual Warewashing/Sink Compartment Requirements
Observation: A sink with at least 3 compartments is not provided for manually washing, rinsing, and sanitizing equipment and utensils.
Correction: Except as specified in paragraph (C) of this section, a sink with at least 3 compartments shall be provided for manually washing, rinsing, and sanitizing equipment and utensils. The 3 compartment sink requirement allows for proper execution of the 3-step manual warewashing procedure. If properly used, the 3 compartments reduce the chance of contaminating the sanitizing water and therefore diluting the strength and efficacy of the chemical sanitizer that may be used. Alternative manual warewashing equipment, allowed under certain circumstances and conditions, must provide for accomplishment of the same 3 steps: 1. Application of cleaners and the removal of soil
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The counter to across the large cutting board is damaged, (peeling paint). The paint inside the basement Artic upright freezer is peeling off.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Service Sink/Numbers and Capacities
Observation: There is no service sink or curbed cleaning facility equipped with a floor drain provided and/or conveniently located for the cleaning of mops or similar wet floor cleaning tools and for the disposal of mop water and similar liquid wastes.
Correction: At least 1 service sink or 1 curbed cleaning facility equipped with a floor drain shall be provided and conveniently located for the cleaning of mops or similar wet floor cleaning tools and for the disposal of mop water and similar liquid wastes. Mop water and similar liquid wastes are contaminated with microorganisms and other filth. Waste water must be disposed of in a sanitary manner that will not contaminate food or food equipment. A service sink or curbed cleaning facility with a drain allows for such disposal.
- Floors, Walls, and Ceilings/Cleanability
Observation: The basement and kitchen ceiling tiles are not designed, constructed, and installed so that it is smooth and easily cleanable.
Correction: Floors, floor coverings, walls, wall coverings, and ceilings shall be designed, constructed and installed so that they are smooth and easily cleanable except for anti-slip floor coverings or applications that may be used for safety reasons and except as specified under section 6-201.14. Floors that are of smooth, durable construction and that are nonabsorbent are more easily cleaned. Requirements and restrictions regarding floor coverings, utility lines, and floor/wall junctures are intended to ensure that regular and effective cleaning is possible and that insect and rodent harborage is minimized.
- Physical Facilities/Repairing
Observation: The men's bathroom floor and wall are damaged. The walk-in cooling unit floor is damaged, (rusty). Some of the basement ceiling tiles are missing.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Cleaning, Frequency and Restrictions (repeated violation)
Observation: All floors corners and edges need cleaning, especially behind the cooking line and large equipment.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
|
02/04/2016 | Routine | |
- RTE, TCS, Date Marking/On-Premises Preparation
Observation: Some ready to eat food containers stored in the walk-in cooling unit prepared and held in the food establishment for more than 24 hours are not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat time/temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
- Equipment Food-Contact Surfaces and Utensils/Cleaning Frequency (Critical)
Observation: The prep table cutting board was not cleaned.
Correction: Equipment food-contact surfaces and utensils shall be cleaned: (1) Before each use with a different type of raw animal food such as beef, fish, lamb, pork, or poultry
|
04/01/2015 | Risk Factor | |
- Time/Temperature Control for Safety Food, Cold Holding (repeated violation)
Observation: Tomato sauce at 74 F, corrected.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The inside of the up-right freezer is rusty.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment/Good Repair and Proper Adjustment (repeated violation)
Observation: The glass door cooler gaskets are damaged.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Equipment/Nonfood-Contact Surfaces/Cleaning Frequency
Observation: The deep fryer and all other cooking equipment need cleaning.
Correction: Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of microorganisms which employees may inadvertently transfer to food. If these areas are not kept clean, they may also provide harborage for insects, rodents, and other pests.
- Cleaning, Frequency and Restrictions
Observation: The floor behind the cooking line needs cleaning.
Correction: Physical facilities shall be cleaned as often as necessary to keep them clean. Cleaning of the physical facilities is an important measure in ensuring the protection and sanitary preparation of food. A regular cleaning schedule should be established and followed to maintain the facility in a clean and sanitary manner.
|
02/12/2015 | Routine | |
- Critical: Safe, Unadulterated, and Honestly Presented/Condition (corrected on site)
Observation: Containers of cottage cheese in walk in observed with an expiration date of 7/6/14. Discarded.
Correction: Food shall be safe, unadulterated, and, as specified under section 3-601.12, honestly presented.
- Food Storage/Preventing Contamination from the Premises
Observation: Stored food is not protected from contamination. Containers of food were stored on the floor in walk in.
Correction: Food shall be protected from contamination by storing the food: (1) In a clean, dry location
- Critical: Time/Temperature Control for Safety Food, Cold Holding (corrected on site)
Observation: Heavy cream at 46 F, sliced tomatoes at 45 F, provolone at 45 F in True 2 dr prep unit. Unit temperature lowered and foods observed at 41 F prior to end of inspection. Cottage cheese at 45 F, sliced tomatoes at 45 F, grape leaves at 44 F on salad bar in plastic containers. Correction by instruction for using metal containers.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, time/temperature control for safety food shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if time/temperature control for safety food remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Nonfood-Contact Surfaces/Nonabsorbent
Observation: The nonfood-contact surface(s) of the ceiling tiles over prep area is(are) not corrosion-resistant, nonabsorbent, and/or smooth.
Correction: Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that requires frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material. Nonfood-contact surfaces of equipment routinely exposed to splash or food debris are required to be constructed of nonabsorbent materials to facilitate cleaning. Equipment that is easily cleaned minimizes the presence of pathogenic organisms, moisture, and debris and deters the attraction of rodents and insects.
- Temperature Measuring Devices
Observation: The Arctic Air 1 door refrigerator in basement is not equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display.
Correction: Cold or hot holding equipment used for potentially hazardous food (time/temperature control for safety food) shall be designed to include and shall be equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display. This section does not apply to equipment for which the placement of a temperature measuring device is not a practical means for measuring the ambient air surrounding the food because of the design, type, and use of the equipment, such as calrod units, heat lamps, cold plates, bainmaries, steamtables, insulated food transport containers, and salad bars. A permanent temperature measuring device is required in any unit storing potentially hazardous (time/temperature control for safety) food because of the potential growth of pathogenic microorganisms should the temperature of the unit exceed Code requirements. In order to facilitate routine monitoring of the unit, the device must be clearly visible.
- Equipment/Good Repair and Proper Adjustment
Observation: The hand sink in the men's restroom was in need of being re-caulked to wall.
The door gasket was torn on the Arctic Air 1 door uprt refrigerator by restrooms.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Refuse/Covering Receptacles (corrected on site)
Observation: Receptacles and/or waste handling units for refuse, recyclables, and/or returnables kept outside the food establishment are not kept covered with tight-fitting lids or doors.
Correction: Receptacles and waste handling units for refuse, recyclables, and returnables shall be kept covered with tight-fitting lids or doors if kept outside the food establishment. Outside receptacles must be constructed with tight-fitting lids or covers to prevent the scattering of the garbage or refuse by birds, the breeding of flies, or then entry of rodents.
- Refuse/Maintaining Refuse Areas and Enclosures
Observation: The ground around the grease receptacle was observed with grease build-up.
Correction: A storage area and enclosure for refuse, recyclables, or returnables shall be maintained free of unnecessary items, as specified under section 6-501.114, and clean. Proper storage and disposal of garbage and refuse are necessary to minimize the development of odors, prevent such waste from becoming an attractant and harborage or breeding place for insects and rodents, and prevent the soiling of food preparation and food service areas. Improperly handled garbage creates nuisance conditions, makes housekeeping difficult, and may be a possible source of contamination of food, equipment, and utensils.
- Poisonous or Toxic Materials/Common Name/Working Containers
Observation: Working containers used for storing poisonous or toxic materials are not clearly and/or individually identified with the common name of the material.
Correction: Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. It is common practice in food establishments to purchase many poisonous or toxic materials including cleaners and sanitizers in bulk containers. Working containers are frequently used to convey these materials to areas where they will be used, resulting in working containers being stored in different locations in the establishment. Identification of these containers with the common name of the material helps prevent the dangerous misuse of the contents.
|
07/10/2014 | Routine | |
1. Garlic breads were stored in a transparent trash bag - (corrected). Always use food grade plastic for storing foods.
2. No hot water at handwashing sink
- Critical: Hands and Arms/When to Wash (corrected on site)
Observation: A food employee did not clean their hands and/or exposed portions of their arms before engaging in food preparation.
Correction: Food employees shall clean their hands and exposed portions of their arms as specified under section 2-301.12 immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles and: (A) After touching bare human body parts other than clean hands and clean, exposed portions of arms
- Package Integrity (corrected on site)
Observation: Several dented cans were found on downstairs storage shelf.
Correction: Food packages shall be in good condition and protect the integrity of the contents so that food is not exposed to adulteration or potential contaminants.
- Critical: Potentially Hazardous Food, Cold Holding (repeated violation)
Observation: The following foods were observed at improper cold holding temperature:
1. Stuffed grape leaves on 4-door salad bar refrigerator - (moved)
2. Cheesecake (48F), Chicken wings (47F) and Shredded cheese (45) in "True" 3 glass door upright refrigerator - (moved to WIC)
3. Provolone (52F), Feta cheese (48F) and Gyro meat (49F) in "True" 2-dr prep refrigerator - (moved)
Correction: (CORRECTED DURING INSPECTION) - Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- RTE, PHF(TCS), Date Marking/On-Premises Preparation
Observation: Lasagna, pasta, sliced cheeses and deli meats, prepared and held in the food establishment for more than 24 hours are not clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded.
Correction: Except when packaging food using a reduced oxygen packaging method as specified under section 3-502.12, refrigerated, ready-to-eat, potentially hazardous food (time/temperature control for safety food) prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, based on the temperature of 5ºC (41ºF) or less for a maximum of 7 days. The day of preparation shall be counted as Day 1. A date marking system that meets the criteria of this section may include: (1) Using a method approved by the regulatory authority for refrigerated, ready-to-eat potentially hazardous food (time/temperature control for safety food) that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine
|
11/05/2013 | Risk Factor | |
- Critical: Potentially Hazardous Food, Cold Holding (corrected on site) (repeated violation)
Observation: 1. Potato salad(46ºF), eggs(46ºF), and cheese(46ºF) in the salad bar cold holding at improper temperatures. 2. Milk(46ºF) and milk(51ºF) in the glass door upright refrigerator cold holding at improper temperatures.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
|
07/09/2013 | Risk Factor | |
- Critical: Packaged and Unpackaged Food-Separation, Packaging, and Segregation/Preventing Food and Ingredient Contamination (corrected on site) (repeated violation)
Observation: Ready-to-eat food is not protected from cross contamination by separating them from raw animal foods. Raw burgers stored above deli cheese in 2 door prep.
Correction: Food shall be protected from cross contamination by separating raw animal foods during storage, preparation, holding, and display from: (a) Raw ready-to-eat food including other raw animal food such as fish for sushi or molluscan shellfish, or other raw ready-to-eat food such as fruits and vegetables, and (b) Cooked ready-to-eat food.
- Food Storage/Preventing Contamination from the Premises
Observation: Stored food is not protected from contamination. Cases of drinks stored on floor by restrooms.
Correction: Food shall be protected from contamination by storing the food: (1) In a clean, dry location
- Critical: Potentially Hazardous Food, Cold Holding (corrected on site) (repeated violation)
Observation: Cooked pasta at 46oF in 2 door prep. Grated pizza cheese at 46oF on ice. Ice added.
Correction: Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under section 3-501.19, and except as specified under paragraph (B) of this section, Potentially Hazardous Food (Time/Temperature Control for Safety Food) shall be maintained at 5ºC (41ºF) or less. Bacterial growth and/or toxin production can occur if potentially hazardous food (time/temperature control for safety food) remains in the temperature "Danger Zone" of 5ºC to 57ºC (41ºF to 135ºF) too long. Up to a point, the rate of growth increases with an increase in temperature within this zone. Beyond the upper limit of the optimal temperature range for a particular organism, the rate of growth decreases. Operations requiring heating or cooling of food should be performed as rapidly as possible to avoid the possibility of bacterial growth.
- Nonfood-Contact Surfaces/Nonabsorbent
Observation: The nonfood-contact surface of the ceiling tiles over ware washing/prep area are not corrosion-resistant, nonabsorbent, and/or smooth.
Correction: Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that requires frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material. Nonfood-contact surfaces of equipment routinely exposed to splash or food debris are required to be constructed of nonabsorbent materials to facilitate cleaning. Equipment that is easily cleaned minimizes the presence of pathogenic organisms, moisture, and debris and deters the attraction of rodents and insects.
- Equipment/Good Repair and Proper Adjustment
Observation: The sliding doors do not open correctly on True 3 door glass uprt.
Bottom of Arctic Air uprt by restrooms has a rusty interior bottom.
Correction: Equipment shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 [Materials for Construction and Repair] and 4-2 [Design and Construction]. Proper maintenance of equipment to manufacturer specifications helps ensure that it will continue to operate as designed. Failure to properly maintain equipment could lead to violations of the associated requirements of the Code that place the health of the consumer at risk. For example, refrigeration units in disrepair may no longer be capable of properly cooling or holding potentially hazardous (time/temperature control for safety) foods at safe temperatures.
- Light Bulbs, Protective Shielding
Observation: The light bulbs for the salad bar are not shielded, coated, or otherwise shatter-resistant.
Correction: Light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed food
- Physical Facilities/Repairing
Observation: Ceiling tiles in hallway observed damaged with water stains and accumulation of mold.
Correction: Physical facilities shall be maintained in good repair. Poor repair and maintenance compromises the functionality of the physical facilities. This requirement is intended to ensure that the physical facilities are properly maintained in order serve their intended purpose.
- Drying Mops
Observation: After use, the mop is not placed in a position that allows it to air-dry without soiling walls, equipment, or supplies.
Correction: After use, mops shall be placed in a position that allows them to air-dry without soiling walls, equipment, or supplies. Mops can contaminate food and food preparation areas if not properly cleaned and stored after use. Mops should be cleaned and dried in a sanitary manner away from food flow areas.
|
03/13/2013 | Routine | |
Restaurant representatives - add corrected or new information about Mom's Pizza Restaurant, 3255 Columbia Pike, Arlington, VA 22204 »