- Food Storage
- Items:
- Food item(s) in storage
- Problems:
- Stored on floor or less than 6 inches above floor
- Corrections:
- Store at least 6 inches above the floor.
- Comment:
- BOX OF SUBWAY WRAPS STORED ON THE FLOOR. STORE ON RACK 6 INCHES ABOVE THE FLOOR.
- General violation description:
- 3-305.11 - (A) Except as specified in ## (B) and (C) of this section, FOOD shall be protected from contamination by storing the FOOD: (1) In a clean, dry location
- Temperature Measuring Devices
- Items:
- Thermometer(s) refrigeration
- Problems:
- Not provided
- Corrections:
- Provide.
- Comment:
- HANGING THERMOMETERS NOT PROVIDED IN THE WALK IN COOLER AND THE 2 DOOR REACH IN COOLER. PROVIDE.
- General violation description:
- 4-204.112 - (A) In a mechanically refrigerated or hot FOOD storage unit, the sensor of a TEMPERATURE MEASURING DEVICE shall be located to measure the air temperature or a simulated product temperature in the warmest part of a mechanically refrigerated unit and in the coolest part of a hot FOOD storage unit. (B) Except as specified in # (C) of this section, cold or hot holding EQUIPMENT used for POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be designed to include and shall be equipped with at least one integral or permanently affixed TEMPERATURE MEASURING DEVICE that is located to allow easy viewing of the device's temperature display. (C) Paragraph (B) of this section does not apply to EQUIPMENT for which the placement of a TEMPERATURE MEASURNG DEVICE is not a practical means for measuring the ambient air surrounding the FOOD because of the design, type, and use of the EQUIPMENT, such as calrod units, heat lamps, cold plates, bainmaries, steam tables, insulated FOOD transport containers, and salad bars. (D) TEMPERATURE MEASURING DEVICES shall be designed to be easily readable. (E) FOOD TEMPERATURE MEASURING DEVICES and water TEMPERATURE MEASURING DEVICES on WAREWASHING machines shall have a numerical scale, printed record, or digital readout in increments no greater than 1°C or 2°F in the intended range of use.(Pf)
|
06/09/2015 | Routine |
- Critical: Potentially Hazardous Food (Ti
- Comment:
- CORRECTED BY HOLDING PHF AT 41F
- General violation description:
- 3-501.16 - Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under 3-501.19, POTENTIALLY HAZARDOUS FOOD shall be maintained: (A) At 60C (140F) or above, except that roasts cooked to a temperature and for a time specified under 3-401.11(B) or reheated as specified in 3-403.11(E) may be held at a temperature of 54C (1300F)
|
12/16/2014 | Follow-up |
- Critical: Controlling Pests
- Comment:
- Observed no gnats. Corrected
- General violation description:
- 6-501.111 - The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the PREMISES by: (A) Routinely inspecting incoming shipments of FOOD and supplies
- Critical: Reheating for Hot Holding
- Comment:
- Observed meat sauce and soups above 135 degrees in hot holding wells. Corrected
- General violation description:
- 3-403.11 - (A) Except as specified under (B) and (C) and in (E) of this section, POTENTIALLY HAZARDOUS FOOD that is cooked, cooled, and reheated for hot holding shall be reheated so that all parts of the FOOD reach a temperature of at least 74C (165F) for 15 seconds. (B) Except as specified under (C) of this section, POTENTIALLY HAZARDOUS FOOD reheated in a microwave oven for hot holding shall be reheated so that all parts of the FOOD reach a temperature of at least 74C (165F) and the FOOD is rotated or stirred, covered, and allowed to stand covered for 2 minutes after reheating. (C) READY-TO-EAT FOOD taken from a commercially processed, HERMETICALLY SEALED CONTAINER, or from an intact package from a FOOD PROCESSING PLANT that is inspected by the FOOD REGULATORY AUTHORITY that has jurisdiction over the plant, shall be heated to a temperature of at least 60C (140F) for hot holding. (D) Reheating for hot holding shall be done rapidly and the time the FOOD is between the temperature specified under 3-501.16(B) or (C) and 74C (165F) may not exceed 2 hours. (E) Remaining unsliced portions of roasts of beef that are cooked as specified under 3-401.11(B) may be reheated for hot holding using the oven parameters and minimum time and temperature conditions specified under 3-401.11(B).
- Good Repair and Proper Adjustm
- Comment:
- Observed no damaged plastic food containers. Corrected
- General violation description:
- 4-501.11 - (A) EQUIPMENT shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 and 4-2. (B) EQUIPMENT components such as doors, seals, hinges, fasteners, and kick plates shall be kept intact, tight, and adjusted in accordance with manufacturer's specifications. (C) Cutting or piercing parts of can openers shall be kept sharp to minimize the creation of metal fragments that can contaminate FOOD when the container is opened.
- Intensity
- Comment:
- Observed working light in storage room. Corrected
- General violation description:
- 6-303.11 - The light intensity shall be: (A) At least 108 lux (10 foot candles) at a distance of 75 cm (30 inches) above the floor, in walk-in refrigeration units and dry FOOD storage areas and in other areas and rooms during periods of cleaning
- Temperature Measuring Devices
- Comment:
- Observed thermometers in all coolers. Corrected
- General violation description:
- 4-204.112 - (A) In a mechanically refrigerated or hot FOOD storage unit, the sensor of a TEMPERATURE MEASURING DEVICE shall be located to measure the air temperature or a simulated product temperature in the warmest part of a mechanically refrigerated unit and in the coolest part of a hot FOOD storage unit. (B) Except as specified in # (C) of this section, cold or hot holding EQUIPMENT used for POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be designed to include and shall be equipped with at least one integral or permanently affixed TEMPERATURE MEASURING DEVICE that is located to allow easy viewing of the device's temperature display. (C) Paragraph (B) of this section does not apply to EQUIPMENT for which the placement of a TEMPERATURE MEASURNG DEVICE is not a practical means for measuring the ambient air surrounding the FOOD because of the design, type, and use of the EQUIPMENT, such as calrod units, heat lamps, cold plates, bainmaries, steam tables, insulated FOOD transport containers, and salad bars. (D) TEMPERATURE MEASURING DEVICES shall be designed to be easily readable. (E) FOOD TEMPERATURE MEASURING DEVICES and water TEMPERATURE MEASURING DEVICES on WAREWASHING machines shall have a numerical scale, printed record, or digital readout in increments no greater than 1°C or 2°F in the intended range of use.(Pf)
- Wiping Cloths, Use Limitation
- Comment:
- Observed raw bucket stored off the ground. Corrected
- General violation description:
- 3-304.14 - (A) Cloths in-use for wiping food spills from TABLEWARE and carry-out containers that occur as FOOD is being served shall be: (1) Maintained dry
|
12/11/2014 | Follow-up |
- Critical: Controlling Pests
- Items:
- Pest(s) gnats
- Problems:
- Present in facility
- Corrections:
- Remove pests from facility.
- Comment:
- Observed a few gnats in dish room and on ceiling/wall near pop machine. Establishment must be free of pests. Eliminate all gnats. Clean all floor drains. Correct immediately,
- General violation description:
- 6-501.111 - The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the PREMISES by: (A) Routinely inspecting incoming shipments of FOOD and supplies
- Critical: Potentially Hazardous Food (Ti
- Items:
- Cold food item(s)
- Problems:
- Stored above 41 degrees f
- Corrections:
- Store below 41 degrees F.
- Comment:
- Observed lunch meats, cut lettuce, tuna, and other potentially hazardous foods at 45- 47 degrees in walk in cooler. Discard all out of temp food in cooler. Potentially hazardous foods must be held at or below 41 degrees at all times. Correct immediately,
- General violation description:
- 3-501.16 - Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under 3-501.19, POTENTIALLY HAZARDOUS FOOD shall be maintained: (A) At 60C (140F) or above, except that roasts cooked to a temperature and for a time specified under 3-401.11(B) or reheated as specified in 3-403.11(E) may be held at a temperature of 54C (1300F)
- Critical: Reheating for Hot Holding
- Items:
- Food item(s) reheated
- Problems:
- Longer than two hours to reach 165 degrees f In steam table
- Corrections:
- Reheat food items quickly.
- Comment:
- Observed soups and meatballs at 98- 112 degrees being reheated in steam unit. Reheat foods to over 165 degrees in microwave before putting them in steam unit. Correct immediately. Food was reheated in microwave at time of inspection.,
- General violation description:
- 3-403.11 - (A) Except as specified under (B) and (C) and in (E) of this section, POTENTIALLY HAZARDOUS FOOD that is cooked, cooled, and reheated for hot holding shall be reheated so that all parts of the FOOD reach a temperature of at least 74C (165F) for 15 seconds. (B) Except as specified under (C) of this section, POTENTIALLY HAZARDOUS FOOD reheated in a microwave oven for hot holding shall be reheated so that all parts of the FOOD reach a temperature of at least 74C (165F) and the FOOD is rotated or stirred, covered, and allowed to stand covered for 2 minutes after reheating. (C) READY-TO-EAT FOOD taken from a commercially processed, HERMETICALLY SEALED CONTAINER, or from an intact package from a FOOD PROCESSING PLANT that is inspected by the FOOD REGULATORY AUTHORITY that has jurisdiction over the plant, shall be heated to a temperature of at least 60C (140F) for hot holding. (D) Reheating for hot holding shall be done rapidly and the time the FOOD is between the temperature specified under 3-501.16(B) or (C) and 74C (165F) may not exceed 2 hours. (E) Remaining unsliced portions of roasts of beef that are cooked as specified under 3-401.11(B) may be reheated for hot holding using the oven parameters and minimum time and temperature conditions specified under 3-401.11(B).
- Good Repair and Proper Adjustm
- Items:
- Equipment
- Problems:
- Broken
- Corrections:
- Repair/replace.
- Comment:
- Observed 6 plastic with chipping or missing pieces near top of containers. Replace. Equipment must be maintained in good working order. Correct immediately,
- General violation description:
- 4-501.11 - (A) EQUIPMENT shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 and 4-2. (B) EQUIPMENT components such as doors, seals, hinges, fasteners, and kick plates shall be kept intact, tight, and adjusted in accordance with manufacturer's specifications. (C) Cutting or piercing parts of can openers shall be kept sharp to minimize the creation of metal fragments that can contaminate FOOD when the container is opened.
- Intensity
- Items:
- Lighting intensity at work levels
- Comment:
- Observed no working light in dry storage room. Provide working light in this area to facilitate cleaning and prevent accidents. Correct immediately,
- General violation description:
- 6-303.11 - The light intensity shall be: (A) At least 108 lux (10 foot candles) at a distance of 75 cm (30 inches) above the floor, in walk-in refrigeration units and dry FOOD storage areas and in other areas and rooms during periods of cleaning
- Nonfood-Contact Surfaces
- Items:
- Nonfood contact surface(s)
- Problems:
- With accumulation of debris
- Corrections:
- Keep clean.
- Comment:
- Observed shelves above 3 compartment sink soiled. Clean the shelves above 3 compartment sink. Non food contact surfaces must be clean. Correct immediately
- General violation description:
- 4-602.13 - NonFOOD-CONTACT SURFACES of EQUIPMENT shall be cleaned at a frequency necessary to preclude accumulation of soil residues.
- Temperature Measuring Devices
- Items:
- Thermometer(s) refrigeration
- Problems:
- Not provided
- Corrections:
- Provide.
- Comment:
- Observed no viable thermometer in walk in cooler and 1 door display coolers. Provide thermometers to these coolers. Correct immediately,
- General violation description:
- 4-204.112 - (A) In a mechanically refrigerated or hot FOOD storage unit, the sensor of a TEMPERATURE MEASURING DEVICE shall be located to measure the air temperature or a simulated product temperature in the warmest part of a mechanically refrigerated unit and in the coolest part of a hot FOOD storage unit. (B) Except as specified in # (C) of this section, cold or hot holding EQUIPMENT used for POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be designed to include and shall be equipped with at least one integral or permanently affixed TEMPERATURE MEASURING DEVICE that is located to allow easy viewing of the device's temperature display. (C) Paragraph (B) of this section does not apply to EQUIPMENT for which the placement of a TEMPERATURE MEASURNG DEVICE is not a practical means for measuring the ambient air surrounding the FOOD because of the design, type, and use of the EQUIPMENT, such as calrod units, heat lamps, cold plates, bainmaries, steam tables, insulated FOOD transport containers, and salad bars. (D) TEMPERATURE MEASURING DEVICES shall be designed to be easily readable. (E) FOOD TEMPERATURE MEASURING DEVICES and water TEMPERATURE MEASURING DEVICES on WAREWASHING machines shall have a numerical scale, printed record, or digital readout in increments no greater than 1°C or 2°F in the intended range of use.(Pf)
- Wiping Cloths, Use Limitation
- Items:
- Wiping cloth(s) wet
- Comment:
- Observed rag bucket stored on the ground. Store at least 6 inches off the ground at all times. Correct immediately,
- General violation description:
- 3-304.14 - (A) Cloths in-use for wiping food spills from TABLEWARE and carry-out containers that occur as FOOD is being served shall be: (1) Maintained dry
|
12/01/2014 | Routine |
- Critical: Equipment Food-Contact Surface
- Comment:
- Observed ice machine clean. Corrected
- General violation description:
- 4-602.11 - (A) EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be cleaned: (1) Except as specified in (B) of this section, before each use with a different type of raw animal FOOD such as beef, FISH, lamb, pork, or POULTRY
|
06/24/2014 | Follow-up |
| No violation noted during this evaluation. | 06/17/2014 | Follow-up |
- Critical: Equipment Food-Contact Surface
- Items:
- Food-contact surface(s) used for nonpotentially hazardous food(s) ice bin(s) in ice machine
- Problems:
- Not cleaned when contaminated
- Corrections:
- Clean properly when contaminated.
- Comment:
- Observed excess black residue in ice machine making parts at customer self serve pop machine. Food contact surfaces must be clean and sanitized. Empty or thaw ice before cleaning. Correct immediately,
- General violation description:
- 4-602.11 - (A) EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be cleaned: (1) Except as specified in (B) of this section, before each use with a different type of raw animal FOOD such as beef, FISH, lamb, pork, or POULTRY
|
06/09/2014 | Routine |
Restaurant representatives - add corrected or new information about Subway, 26671 Grand River Ave, Redford, MI 48240 »