- Critical: Manual and Mechanical Warewash
- Items:
- Chlorine solution concentration
- Locations:
- 3-compartment sink(s)
- Problems:
- Below 25 ppm
- Corrections:
- Provide correct concentration as stated above.
- Comment:
- A CHEMICAL CHLORINE SOLUTION MUST HAVE A MINIMUM TEMPERATURE BASED ON THE CONCENTRATION OF THE SOLUTION. OBSERVED EMPLOYEE NOT PROPERLY USING WASH, RINSE, SANITIZE PROCEDURE WHEN WASHING UTENSILS. WHEN USING A CHLORINE SANITIZER USE ONLY THE SANITIZE SINK WITH THE APPROPRIATE PPM PER EPA USE INSTRUCTIONS ON THE BOTTLE. , CORRECTED AT TIME OF INSPECTION EMPLOYEE IMMEDIATELY READ INSTRUCTIONS FOR THE APPROPRIATE PPM AND SANITIZER TEST STRIP READ AT 200PPM.
- General violation description:
- 4-501.114 - A chemical SANITIZER used in a SANITIZING solution for a manual or mechanical operation at exposure times specified under 4-703.11(C) shall be listed in 21 CFR 178.1010 Sanitizing solutions, shall be used in accordance with the EPA-approved manufacturer's label use instructions, and shall be used as follows: (A) A chlorine solution shall have a minimum temperature based on the concentration and pH of the solution as listed in the following chart
- Good Repair and Proper Adjustm
- Items:
- Equipment
- Locations:
- walk-in cooler(s)
- Problems:
- Broken
- Corrections:
- Repair/replace.
- Comment:
- EQUIPMENT COMPOTENTS SUCH AS DOORS AND SEALS MUST BE KEPT INTACT AND TIGHT. OBSERVED DOOR ON WALK IN COOLER NOT PROPERLY CLOSING. REPAIR DOOR HANDLE OR SEAL TO MAKE A TIGHT FIT.
- General violation description:
- 4-501.11 - (A) EQUIPMENT shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 and 4-2. (B) EQUIPMENT components such as doors, seals, hinges, fasteners, and kick plates shall be kept intact, tight, and adjusted in accordance with manufacturer's specifications. (C) Cutting or piercing parts of can openers shall be kept sharp to minimize the creation of metal fragments that can contaminate FOOD when the container is opened.
- Nonfood-Contact Surfaces
- Items:
- Nonfood contact surface(s)
- Locations:
- walk-in cooler(s)
- Problems:
- With accumulation of debris
- Corrections:
- Keep clean.
- Comment:
- NON-FOOD CONTACT SURFACES MUST BE CLEANED AT A FREQUENCY NECESSARY TO REDUCE THE BUILD UP OF DEBRIS. OBSERVED IN WALK IN COOLER MOLD ON THE CEILING AND WALLS. INCREASE CLEANING FREQUENCY TO REDUCE AMOUNT OF DEBRIS.
- General violation description:
- 4-602.13 - NonFOOD-CONTACT SURFACES of EQUIPMENT shall be cleaned at a frequency necessary to preclude accumulation of soil residues.
|
01/27/2015 | Routine |
| No violation noted during this evaluation. | 08/01/2014 | Follow-up |
- Critical: Potentially Hazardous Food (Ti
- Items:
- Cold food item(s)
- Problems:
- Stored above 41 degrees f
- Corrections:
- Store below 41 degrees F.
- Comment:
- Observed corned beef, salami, and shell eggs in the front display cooler at temperatures ranging from 45-51 degrees F. Potentially hazardous foods must be held below 41 degrees F. Repair or replace the cooler. Discard these foods after 4 hours in the temperature danger zone of 41-135 degrees F.
- General violation description:
- 3-501.16 - Except during preparation, cooking, or cooling, or when time is used as the public health control as specified under 3-501.19, POTENTIALLY HAZARDOUS FOOD shall be maintained: (A) At 60C (140F) or above, except that roasts cooked to a temperature and for a time specified under 3-401.11(B) or reheated as specified in 3-403.11(E) may be held at a temperature of 54C (1300F)
- Nonfood-Contact Surfaces
- Items:
- Nonfood contact surface(s)
- Problems:
- Soiled
- Corrections:
- Keep clean.
- Comment:
- Observed food debris on the dough maker. Non-food contact equipment must be kept clean. The dough maker was cleaned to sight and touch in my presence. Violation corrected.
- General violation description:
- 4-602.13 - NonFOOD-CONTACT SURFACES of EQUIPMENT shall be cleaned at a frequency necessary to preclude accumulation of soil residues.
- Outer Openings, Protected
- Items:
- Outer opening(s)
- Problems:
- Not sealed to prevent pest entry
- Corrections:
- Seal to prevent pest entry.
- Comment:
- Observed back door propped open. Outer openeings must be protected from entry of insects and rodents. The door was closed in my presence. Violation corrected.
- General violation description:
- 6-202.15 - (A) Except as specified in ## (B), (C), and (E) and under # (D) of this section, outer openings of a FOOD ESTABLISHMENT shall be protected against the entry of insects and rodents by: (1) Filling or closing holes and other gaps along floors, walls, and ceilings
- Temperature Measuring Devices
- Items:
- Thermometer(s)
- Problems:
- Not provided
- Corrections:
- Provide.
- Comment:
- Observed no thermometer in the coffee and creamer cooler in dining room. A thermometer was provided in my presence. Violation corrected.
- General violation description:
- 4-204.112 - (A) In a mechanically refrigerated or hot FOOD storage unit, the sensor of a TEMPERATURE MEASURING DEVICE shall be located to measure the air temperature or a simulated product temperature in the warmest part of a mechanically refrigerated unit and in the coolest part of a hot FOOD storage unit. (B) Except as specified in # (C) of this section, cold or hot holding EQUIPMENT used for POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be designed to include and shall be equipped with at least one integral or permanently affixed TEMPERATURE MEASURING DEVICE that is located to allow easy viewing of the device's temperature display. (C) Paragraph (B) of this section does not apply to EQUIPMENT for which the placement of a TEMPERATURE MEASURNG DEVICE is not a practical means for measuring the ambient air surrounding the FOOD because of the design, type, and use of the EQUIPMENT, such as calrod units, heat lamps, cold plates, bainmaries, steam tables, insulated FOOD transport containers, and salad bars. (D) TEMPERATURE MEASURING DEVICES shall be designed to be easily readable. (E) FOOD TEMPERATURE MEASURING DEVICES and water TEMPERATURE MEASURING DEVICES on WAREWASHING machines shall have a numerical scale, printed record, or digital readout in increments no greater than 1°C or 2°F in the intended range of use.(Pf)
- Ventilation Hood Systems, Adeq
- Items:
- Ventilation hood
- Problems:
- Inadequate
- Corrections:
- Provide adequate ventilation.
- Comment:
- Observed the temperature in the oven room at 93 degrees F. The dining room is at 82 degrees F. Check the exhaust hoods for adequate ventilation and provide a receipt that work was done.
- General violation description:
- 4-301.14 - Ventilation hood systems and devices shall be sufficient in number and capacity to prevent grease or condensation from collecting on walls and ceilings
- Wiping Cloths, Use Limitation
- Items:
- Wiping cloth(s)
- Problems:
- Not completely submerged in sanitizing solution
- Corrections:
- Store wiping cloths completely submersed in sanitizer.
- Comment:
- Observed wiping cloths not stored in sanitizing solution when not in use. Store wiping cloths in 50-100 ppm of chlorine solution in the wiping cloth pail.
- General violation description:
- 3-304.14 - (A) Cloths in-use for wiping food spills from TABLEWARE and carry-out containers that occur as FOOD is being served shall be: (1) Maintained dry
|
07/22/2014 | Routine |
| No violation noted during this evaluation. | 01/27/2014 | Follow-up |
- Critical: Handwashing Cleanser, Availabi
- Items:
- Soap
- Problems:
- Not provided
- Corrections:
- Provide.
- Comment:
- Observed no soap for the rear and middle handsinks. Soap must be provided. Correct immediately.
- General violation description:
- 6-301.11 - Each HANDWASHING SINK or group of 2 adjacent HANDWASHING SINKS shall be provided with a supply of hand cleaning liquid, powder, or bar soap.(Pf)
- Critical: Responsibility of Permit Holde
- Items:
- Person-in-charge
- Problems:
- Fail to require employees to report illness as rule requires
- Corrections:
- Require reporting as stated above.
- Comment:
- Employee health forms 1A and 1B have not been filled out and signed by employees. Have employees fill out and sign forms.
- General violation description:
- 2-201.11 - The PERMIT HOLDER shall require FOOD EMPLOYEE applicants to whom a conditional offer of employment is made and FOOD EMPLOYEES to report to the PERSON IN CHARGE, information about their health and activities as they relate to diseases that are transmissible through FOOD, AND report the information in a manner that allows the PERSON IN CHARGE to prevent the likelihood of foodborne disease transmission.
- Critical: System Maintained in Good Repa
- Items:
- Plumbing system
- Problems:
- Not maintained
- Corrections:
- Maintain in good repair
- Comment:
- Observed condenser in walk-in cooler leaking water on shelves and floor. Plumbing must be maintained. Repair or replace the condenser.
- General violation description:
- 5-205.15 - A PLUMBING SYSTEM shall be: (A) Repaired according to LAW
- Designated Areas
- Items:
- Locker(s)/employee storage area(s)
- Problems:
- Contaminates
- Corrections:
- Relocate to a designated area that does not contaminate items or surfaces.
- Comment:
- Observed two employee coats hung on dry storage shelf unit. Store employee items in designated area away from food.
- General violation description:
- 6-403.11 - (A) Areas designated for EMPLOYEES to eat, drink, and use tobacco shall be located so that FOOD, EQUIPMEBT, LINENS, and SINGLE-SERVICE and SINGLE-USE ARTICLES are protected from contamination. (B) Lockers or other suitable facilities shall be located in a designated room or area where contamination of FOOD, EQUIPMENT, UTENSILS, LINENS, and SINGLE-SERVICE and SINGLE-USE ARTICLES can not occur.
- Effectiveness
- Items:
- Hair restraint
- Problems:
- Not worn on face
- Corrections:
- Provide beard net.
- Comment:
- Observed food handler with beard not wearing a beard net. Hair must be covered. Provide a beard net.
- General violation description:
- 2-402.11 - (A) Except as provided in # (B) of this section, FOOD EMPLOYEES shall wear hair restraints such as hats, hair coverings or nets, beard restraints, and clothing that covers body hair, that are designed and worn to effectively keep their hair from contacting exposed FOOD
- Handwashing Signage
- Items:
- Handwashing signage
- Problems:
- Not provided
- Corrections:
- Provide.
- Comment:
- Observed no hand washing sign for rear hand sink. Provide a sign.
- General violation description:
- 6-301.14 - A sign or poster that notifies FOOD EMPLOYEES to wash their hands shall be provided at all HANDWASHING SINKS used by FOOD EMPLOYEES and shall be clearly visible to FOOD EMPLOYEES.
|
01/17/2014 | Routine |
| No violation noted during this evaluation. | 01/16/2014 | Routine |
- Critical: Backflow Prevention
- Comment:
- CORRECTED: THE WALK-IN COOLER CONDENSATE DRAIN LINE HAS BEEN PROPERLY AIR GAPPED.
- General violation description:
- 5-402.11 - (A) Except as specified in (B) and (C) of this section, a direct connection may not exist between the SEWAGE system and a drain originating from EQUIPMENT in which FOOD, portable EQUIPMENT, or UTENSILS are placed. (B) If allowed by LAW, a WAREWASHING machine may have a direct connection between its waste outlet and a floor drain when the machine is located within 1.5 m (5 feet) of a trapped floor drain and the machine outlet is connected to the inlet side of a properly vented floor drain trap. (C) If allowed by LAW, a WAREWASHING or culinary sink may have a direct connection.
- Critical: Cooling, Heating, and Holding
- Comment:
- CORRECTED: A 2-DOOR SANDWICH PREP COOLER HAS BEEN PROVIDED AT THE FRONT COUNTER AT TIME OF RE-INSPECTION.
- General violation description:
- 4-301.11 - EQUIPMENT for cooling and heating FOOD, and holding cold and hot FOOD, shall be sufficient in number and capacity to provide FOOD temperatures as specified under Chapter 3. (Pf)
- Critical: Equipment, Food-Contact Surfac
- Comment:
- CORRECTED: ALL SURFACES HAVE BEEN CLEANED TO SIGHT AND TOUCH.
- General violation description:
- 4-601.11 - (A) EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be clean to sight and touch. (B) The FOOD-CONTACT SURFACES of cooking EQUIPMENT and pans shall be kept free of encrusted grease deposits and other soil accumulations. N (C) NonFOOD-CONTACT SURFACES of EQUIPMENT shall be kept free of an accumulation of dust, dirt, FOOD residue, and other debris. N
- Critical: Handwashing Sinks
- Comment:
- CORRECTED: A HANDWASH SINK HAS BEEN PROVIDED IN THE BACK PRODUCTION AREA.
- General violation description:
- 5-204.11 - Placement A handwashing facility shall be located: (A) To allow convenient use by EMPLOYEES in FOOD preparation, FOOD dispensing, and WAREWASHING areas
- Drying Mops
- Comment:
- CORRECTED: THE MOP HANGER HAS BEEN RE-INSTALLED OVER THE MOP SINK.
- General violation description:
- 6-501.16 - After use, mops shall be placed in a position that allows them to air-dry without soiling walls, EQUIPMENT, or supplies.
- Fixed Equipment, Elevation or
- Comment:
- CORRECTED: 1. THE FLOOR SINK HAS BEEN CAULKED TO THE FLOOR WITH CAULK (SEAL THE FLOOR SINK WITH GROUT OR CONCRETE (PRIOR TO FIRST ROUTINE INSP). 2. THE MOP SINK HAS BEEN SEALED TO FLOOR.
- General violation description:
- 4-402.12 - (A) Except as specified in ## (B) and (C) of this section, floor-mounted EQUIPMETN that is not EASILY MOVABLE shall be SEALED to the floor or elevated on legs that provide at least a 15 centimeter (6 inch) clearance between the floor and the EQUIPMENT. (B) If no part of the floor under the floor-mounted EQUIPMENT is more than 15 centimeters (6 inches) from the point of cleaning access, the clearance space may be only 10 centimeters (4 inches). (C) This section does not apply to display shelving units, display refrigeration units, and display freezer units located in the CONSUMER shopping areas of a retail FOOD store, if the floor under the units is maintained clean. (D) Except as specified in # (E) of this section, COUNTER-MOUNTED EQUIPMENT that is not EASILY MOVABLE shall be elevated on legs that provide at least a 10 centimeter (4 inch) clearance between the table and the EQUIPMENT. (E) The clearance space between the table and COUNTER-MOUNTED EQUIPMENT may be: (1) 7.5 centimeters (3 inches) if the horizontal distance of the table top under the EQUIPMENT is no more than 50 centimeters (20 inches) from the point of access for cleaning
- Floor and Wall Junctures, Cove
- Comment:
- CORRECTED: THE COVE BASE HAS BEEN RE-INSTALLED AT THE WALK-IN COOLER. (REMOVE THE IMPROPERLY INSTALLED CAULK AND CAULK ALL SEAMS TO A SMOOTH CLEANABLE SURFACES).
- General violation description:
- 6-201.13 - (A) In FOOD ESTABLISHMENTS in which cleaning methods other than water flushing are used for cleaning floors, the floor and wall junctures shall be coved and closed to no larger than 1 mm (one thirty-second inch). (B) The floors in FOOD ESTABLISHMENTS in which water flush cleaning methods are used shall be provided with drains and be graded to drain, and the floor and wall junctures shall be coved and SEALED.
- Good Repair and Proper Adjustm
- Comment:
- CORRECTED: A PROPER DUNNAGE RACK HAS BEEN PROVIDED.
- General violation description:
- 4-501.11 - (A) EQUIPMENT shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 and 4-2. (B) EQUIPMENT components such as doors, seals, hinges, fasteners, and kick plates shall be kept intact, tight, and adjusted in accordance with manufacturer's specifications. (C) Cutting or piercing parts of can openers shall be kept sharp to minimize the creation of metal fragments that can contaminate FOOD when the container is opened.
|
12/02/2013 | Follow-up |
Restaurant representatives - add corrected or new information about Detroit Bagel, 18760 Middlebelt Rd, Livonia, MI 48152 »