- Critical: Handwashing Sink, Installation
- Comment:
- CORRECTED. HOT WATER (100*F AND ABOVE) AT THE HAND WASH SINK (LEFT SIDE) IN THE MEN'S RESTROOM.
- General violation description:
- 5-202.12 - (A) A HANDWASHING SINK shall be equipped to provide water at a temperature of at least 38°C (100°F) through a mixing valve or combination faucet. (Pf) (B) A steam mixing valve may not be used at a HANDWASHING SINK. (C) A self-closing, slow-closing, or metering faucet shall provide a flow of water for at least 15 seconds without the need to reactivate the faucet. (D) An automatic handwashing facility shall be installed in accordance with manufacturer's instructions.
|
05/01/2015 | Follow-up |
- Critical: Handwashing Sink, Installation
- Items:
- Handwashing facility
- Locations:
- men's restroom
- Problems:
- Lack of hot water
- Corrections:
- Provide hot water.
- Comment:
- IN THE MEN'S RESTROOM LOCATED NEAR THE CAFETERIA, THE SINK ON THE LEFT NO RUNNING HOT WATER. PROVIDE HOT WATER. ,
- General violation description:
- 5-202.12 - (A) A HANDWASHING SINK shall be equipped to provide water at a temperature of at least 38°C (100°F) through a mixing valve or combination faucet. (Pf) (B) A steam mixing valve may not be used at a HANDWASHING SINK. (C) A self-closing, slow-closing, or metering faucet shall provide a flow of water for at least 15 seconds without the need to reactivate the faucet. (D) An automatic handwashing facility shall be installed in accordance with manufacturer's instructions.
- Effectiveness
- Items:
- Hair restraint
- Problems:
- Not worn on head/hair
- Corrections:
- Provide hat or hair net.
- Comment:
- OBSERVED IN THE ASSISTANT PRINCIPAL OFFICE THERE WAS SCHOOL EMPLOYEE SERVING POPCORN WITH A HAIRNET. , OBSERVED IN THE ASSISTANT PRINCIPAL OFFICE THERE WAS SCHOOL EMPLOYEE SERVING POPCORN WITHOUT A HAIRNET.
- General violation description:
- 2-402.11 - (A) Except as provided in # (B) of this section, FOOD EMPLOYEES shall wear hair restraints such as hats, hair coverings or nets, beard restraints, and clothing that covers body hair, that are designed and worn to effectively keep their hair from contacting exposed FOOD
- Handwashing Signage
- Items:
- Handwashing signage
- Locations:
- men's restroom
- Problems:
- Not provided At hand sink
- Corrections:
- provide
- General violation description:
- 6-301.14 - A sign or poster that notifies FOOD EMPLOYEES to wash their hands shall be provided at all HANDWASHING SINKS used by FOOD EMPLOYEES and shall be clearly visible to FOOD EMPLOYEES.
- Light Bulbs, Protective Shield
- Items:
- Light shielding light shield(s)
- Locations:
- Ventilation hood canopy
- Problems:
- Not provided
- Corrections:
- Provide adequate light shields and end caps or shatter-proof bulbs.
- Comment:
- LIGHT SHIELDS NOT PROVIDED ON BULBS UNDER VENTILATION HOOD CANOPY.
- General violation description:
- 6-202.11 - (A) Except as specified in # (B) of this section, light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed FOOD
- Nonfood-Contact Surfaces
- Items:
- Nonfood contact surface(s)
- Locations:
- Vent hood(s) and Filters
- Problems:
- With accumulation of debris
- Corrections:
- Keep clean.
- General violation description:
- 4-602.13 - NonFOOD-CONTACT SURFACES of EQUIPMENT shall be cleaned at a frequency necessary to preclude accumulation of soil residues.
- Repairing
- Items:
- Physical facilities
- Locations:
- Vent hood(s) and Filters
- Problems:
- In poor repair
- Corrections:
- Repair/replace.
- Comment:
- FILTERS IN THE VENTILATION HOOD AREA WERE NOT FITTED PROPERLY IN THE SPACE. ADJUST THE FILTERS PROPERLY.
- General violation description:
- 6-501.11 - PHYSICAL FACILITIES shall be maintained in good repair.
- Toilet Room Receptacle, Covere
- Items:
- Covered waste receptacle(s) in ladies restroom
- Problems:
- Not provided
- Corrections:
- Provide.
- General violation description:
- 5-501.17 - A toilet room used by females shall be provided with a covered receptacle for sanitary napkins.
|
04/15/2015 | Routine |
- Critical: Equipment, Food-Contact Surfac
- Items:
- Food-contact surface(s) Equipment
- Problems:
- Soiled
- Corrections:
- Clean prior to opening.
- Comment:
- Observed over 6 metal containers in storage with excess food debris on them. Food contact surfaces must be clean and sanitized. Clean these items. Correct immediately. Corrected at time of inspection by education and by cleaning and sanitizing containers. Corrected
- General violation description:
- 4-601.11 - (A) EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be clean to sight and touch. (B) The FOOD-CONTACT SURFACES of cooking EQUIPMENT and pans shall be kept free of encrusted grease deposits and other soil accumulations. N (C) NonFOOD-CONTACT SURFACES of EQUIPMENT shall be kept free of an accumulation of dust, dirt, FOOD residue, and other debris. N
- Equipment, Utensils, Linens, a
- Items:
- Single-service/single-use article(s)
- Problems:
- Exposed to dust, splash, or other contaminates
- Corrections:
- Store in protected manner.
- Comment:
- Observed disposable gloves stored on shelf right next to hand sink on cook line. Do not store utensils/gloves next to hand sink. Correct immediately. Corrected at time of inspection by removing gloves from next to hand sink. Corrected
- General violation description:
- 4-903.11 - (A) Except as specified in # (D) of this section, cleaned EQUIPMENT and UTENSILS, laundered LINENS, and SINGLE-SERVICE and SINGLE-USE ARTICLES shall be stored: (1) In a clean, dry location
|
10/21/2014 | Routine |
- Cleaning, Frequency and Restri
- Items:
- Physical facilities/structures
- Problems:
- Not clean
- Corrections:
- Keep clean
- Comment:
- OBSERVED FILTERS UNDER HOOD ABOVE OVENS WITH EXCESS DUST ON THEM. CLEAN THE FILTERS. PHYSICAL FACILITES MUST BE CLEAN. CORRECT IMMEDIATELY
- General violation description:
- 6-501.12 - (A) PHYSICAL FACILITIES shall be cleaned as often as necessary to keep them clean. (B) Except for cleaning that is necessary due to a spill or other accident, cleaning shall be done during periods when the least amount of FOOD is exposed such as after closing.
- Good Repair and Proper Adjustm
- Items:
- Equipment
- Problems:
- Do not meet requirements of rule
- Corrections:
- Repair/replace to meet requirements of rule.
- Comment:
- OBSERVED 2 DOOR (2 SIDED) VICTORY COOLER AT 48 DEGREES AIR TEMPERATURE. NO HAZARDOUS FOODS IN THIS COOLER AT TIME OF INSPECTION. DO NOT STORE POTENTIALLY HAZARDOUS FOODS IN THIS COOLER UNTIL IT HOLDS FOOD AT 41 DEGREES OR LESS. COOLER MUST BE AT 38 DEGREES OR LESS. CORRECT IMMEDIATELY
- General violation description:
- 4-501.11 - (A) EQUIPMENT shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 and 4-2. (B) EQUIPMENT components such as doors, seals, hinges, fasteners, and kick plates shall be kept intact, tight, and adjusted in accordance with manufacturer's specifications. (C) Cutting or piercing parts of can openers shall be kept sharp to minimize the creation of metal fragments that can contaminate FOOD when the container is opened.
|
04/10/2014 | Routine |
- Critical: Using a Handwashing Sink
- Items:
- Handwashing sink(s)
- Problems:
- Not easily accessible Items stored In front of
- Corrections:
- Remove items from handsink. Do not store items at handsink.
- Comment:
- OBSERVED CART STORED IN FRONT OF HAND SINK NEAR DISHMACHINE. HAND SINKS MUST BE FULLY ACCESSIBLE AT ALL TIMES. CORRECT IMMEDIATELY. CORRECTED BY EDUCATION AND BY MOVING CART FROM IN FRONT OF SINK. CORRECTED
- General violation description:
- 5-205.11 - (A) A HANDWASHING SINK shall be maintained so that it is accessible at all times for EMPLOYEE use. (Pf) (B) A HANDWASHING SINK may not be used for purposes other than handwashing. (Pf) (C) An automatic handwashing facility shall be used in accordance with manufacturer's instructions. (Pf)
- System Maintained in Good Repa
- Items:
- Plumbing system drain line(s)
- Problems:
- Not maintained
- Corrections:
- Maintain in good repair
- Comment:
- OBSERVED LEAK UNDER 2ND COMPARTMENT OF 3 COMPARTMENT SINK. FIX LEAK UNDER SINK. PLUMBING SYSTEM MUST BE MAINTAINED. CORRECT IMMEDIATELY
- General violation description:
- 5-205.15 - A PLUMBING SYSTEM shall be: (A) Repaired according to LAW
|
10/17/2013 | Routine Inspection |
- Critical: Person in Charge
- Items:
- Person-in-charge
- Problems:
- Not ensuring compliance
- Corrections:
- Person-in-charge must ensure compliance with items listed above.
- Comment:
- Observed daily temperature charts not being filled out for kitchen coolers. Food temperatures must be monitored on a daily basis. Temperatures were checked and recorded in my presence. Violation corrected.
- General violation description:
- 2-103.11 - The PERSON IN CHARGE shall ensure that: (A) FOOD ESTABLISHMENT operations are not conducted in a private home or in a room used as living or sleeping quarters as specified under # 6-202.111
- Critical: Temperature Measuring Devices,
- Items:
- Thermometer(s)
- Problems:
- Not accurate
- Corrections:
- Calibrate to requirement above.
- Comment:
- Observed broken indicating thermometer in the juice cooler at serving line. Thermometers must be accurate. This thermometer was replaced with a new one in my presence. Violation corrected.
- General violation description:
- 4-203.11 - (A) FOOD TEMPERATURE MEASURING DEVICES that are scaled only in Celsius or dually scaled in Celsius and Fahrenheit shall be accurate to ±1°C in the intended range of use. (Pf) (B) FOOD TEMPERATURE MEASURING DEVICES that are scaled only in Fahrenheit shall be accurate to ±2°F in the intended range of use. (Pf)
- Nonfood-Contact Surfaces
- Items:
- Nonfood contact surface(s)
- Problems:
- Soiled
- Corrections:
- Keep clean.
- Comment:
- Observed build-up of dust on backs of the ovens. Non-food contact surfaces must be kept clean. Clean to sight and touch.
- General violation description:
- 4-602.13 - NonFOOD-CONTACT SURFACES of EQUIPMENT shall be cleaned at a frequency necessary to preclude accumulation of soil residues.
|
10/23/2012 | Routine |
- Clean Freq, Nonfood-Contact Su
- Items:
- Nonfood contact surface(s)
- Problems:
- Soiled
- Corrections:
- Keep clean.
- Comment:
- Clean the fryer behind the panel door to sight and touch.
- General violation description:
- 4-602.13 - NonFOOD-CONTACT SURFACES of EQUIPMENT shall be cleaned at a frequency necessary to preclude accumulation of soil residues.
- Clean Freq, Nonfood-Contact Su
- Items:
- Nonfood contact surface(s)
- Problems:
- Rusty
- Corrections:
- Repair/replace.
- Comment:
- Observed rusty base of Hobart mixer. Repair the mixer to provide a smooth and easily cleanable surface.
- General violation description:
- 4-202.16 - NonFOOD-CONTACT SURFACES shall be free of unnecessary ledges, projections, and crevices, and designed and constructed to allow easy cleaning and to facilitate maintenance.
- Clean, Vent. Sys., Prev. Disch
- Items:
- Ventilation system
- Problems:
- Not clean
- Corrections:
- Keep clean
- Comment:
- Baffle filters and fire suppression system are very dusty. Clean to sight and touch.
- General violation description:
- 6-501.14 - (A) Intake and exhaust air ducts shall be cleaned and filters changed so they are not a source of contamination by dust, dirt, and other materials. (B) If vented to the outside, ventilation systems may not create a public health HAZARD or nuisance or unLAWful discharge.
- Cleaning, Frequency/Restrictio
- Items:
- Physical facilities/structures
- Problems:
- Not clean
- Corrections:
- Keep clean
- Comment:
- Clean the floor of the dry storage room to sight and touch especially under the bottom shelves of storage racks.
- General violation description:
- 6-501.12 - (A) PHYSICAL FACILITIES shall be cleaned as often as necessary to keep them clean. (B) Except for cleaning that is necessary due to a spill or other accident, cleaning shall be done during periods when the least amount of FOOD is exposed such as after closing.
|
04/03/2012 | Routine Inspection |
- Clean Freq, Nonfood-Contact Su
- Items:
- Nonfood contact surface(s)
- Problems:
- Rusty
- Corrections:
- Repair/replace.
- Comment:
- Observed rusty base of Hobart mixer. Non-food contact surfaces must be smooth and easily cleanable. Repair or replace the mixer.
- General violation description:
- 4-202.16 - NonFOOD-CONTACT SURFACES shall be free of unnecessary ledges, projections, and crevices, and designed and constructed to allow easy cleaning and to facilitate maintenance.
- Clean, Vent. Sys., Prev. Disch
- Items:
- Ventilation system
- Problems:
- Not clean
- Corrections:
- Keep clean
- Comment:
- Observed dusty baffle filters and fire suppression system in exhaust hood. Clean to sight and touch.
- General violation description:
- 6-501.14 - (A) Intake and exhaust air ducts shall be cleaned and filters changed so they are not a source of contamination by dust, dirt, and other materials. (B) If vented to the outside, ventilation systems may not create a public health HAZARD or nuisance or unLAWful discharge.
- Wiping Cloths, Use Limitation
- Items:
- Wiping cloth(s)
- Problems:
- Stored in
- Comment:
- Observed wiping cloth stored in sanitizer at only 100 ppm of quaternary ammonia. The person in charge provided new sanitizing solution to the wiping cloth pail which was at 200 ppm of quaternary ammonia. Violation corrected.
- General violation description:
- 3-304.14 - (A) Cloths in-use for wiping food spills from TABLEWARE and carry-out containers that occur as FOOD is being served shall be: (1) Maintained dry
|
10/28/2011 | Routine Inspection |
- Temperature Measuring Devices
- Items:
- Thermometer(s)
- Problems:
- Not provided
- Corrections:
- Provide.
- Comment:
- Observed no thermometer in the pizza prep cooler. A thermometer was provided in my presence. Violation corrected.
- General violation description:
- 4-204.112 - (A) In a mechanically refrigerated or hot FOOD storage unit, the sensor of a TEMPERATURE MEASURING DEVICE shall be located to measure the air temperature or a simulated product temperature in the warmest part of a mechanically refrigerated unit and in the coolest part of a hot FOOD storage unit. (B) Except as specified in # (C) of this section, cold or hot holding EQUIPMENT used for POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be designed to include and shall be equipped with at least one integral or permanently affixed TEMPERATURE MEASURING DEVICE that is located to allow easy viewing of the device's temperature display. (C) Paragraph (B) of this section does not apply to EQUIPMENT for which the placement of a TEMPERATURE MEASURNG DEVICE is not a practical means for measuring the ambient air surrounding the FOOD because of the design, type, and use of the EQUIPMENT, such as calrod units, heat lamps, cold plates, bainmaries, steam tables, insulated FOOD transport containers, and salad bars. (D) TEMPERATURE MEASURING DEVICES shall be designed to be easily readable. (E) FOOD TEMPERATURE MEASURING DEVICES and water TEMPERATURE MEASURING DEVICES on WAREWASHING machines shall have a numerical scale, printed record, or digital readout in increments no greater than 1°C or 2°F in the intended range of use.(Pf)
- Temperature Measuring Devices
- Items:
- Thermometer(s)
- Problems:
- Not provided
- Corrections:
- Provide.
- Comment:
- Observed no thermometer in the pizza prep cooler. A thermometer was provided in my presence. Violation corrected.
- General violation description:
- 4-204.112 - (A) In a mechanically refrigerated or hot FOOD storage unit, the sensor of a TEMPERATURE MEASURING DEVICE shall be located to measure the air temperature or a simulated product temperature in the warmest part of a mechanically refrigerated unit and in the coolest part of a hot FOOD storage unit. (B) Except as specified in # (C) of this section, cold or hot holding EQUIPMENT used for POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be designed to include and shall be equipped with at least one integral or permanently affixed TEMPERATURE MEASURING DEVICE that is located to allow easy viewing of the device's temperature display. (C) Paragraph (B) of this section does not apply to EQUIPMENT for which the placement of a TEMPERATURE MEASURNG DEVICE is not a practical means for measuring the ambient air surrounding the FOOD because of the design, type, and use of the EQUIPMENT, such as calrod units, heat lamps, cold plates, bainmaries, steam tables, insulated FOOD transport containers, and salad bars. (D) TEMPERATURE MEASURING DEVICES shall be designed to be easily readable. (E) FOOD TEMPERATURE MEASURING DEVICES and water TEMPERATURE MEASURING DEVICES on WAREWASHING machines shall have a numerical scale, printed record, or digital readout in increments no greater than 1°C or 2°F in the intended range of use.(Pf)
|
10/18/2010 | Routine Inspection |
- Critical: Ready-to-Eat Food, Disposition
- Items:
- Ready to eat, potentially hazardous food(s)
- Problems:
- Beyond consume by date
- Corrections:
- Discard.
- Comment:
- Observed tuna salad in cooler with date mark expiration of 9/30/09. Tuna has been expired for 5 days. Ready-to-eat foods that have not been used by their expiration date must be discarded. The person in charge discarded the tuna salad in my presence. Violation corrected.
- General violation description:
- 3-501.18 - (A) A FOOD specified under 3-501.17(A) shall be discarded if not consumed within: (1) 7 calendar days from the date of preparation if the FOOD is maintained at 5C (41F) or less
- Food Temperature Measuring Dev
- Items:
- Food thermometer(s)
- Problems:
- Not provided
- Corrections:
- Provide.
- Comment:
- Observed missing thermometers for the Victory cooler at the serving line and the pizza prep cooler in kitchen. Provide conspicuous thermometers in both coolers.
- General violation description:
- 4-302.12 - (A) FOOD TEMPERATURE MEASURING DEVICES shall be provided and readily accessible for use in ensuring attainment and maintenance of FOOD temperatures as specified under Chapter 3. (Pf) (B) A TEMPERATURE MEASURING DEVICE with a suitable small-diameter probe that is designed to measure the temperature of thin masses shall be provided and readily accessible to accurately measure the temperature in thin FOODS such as MEAT patties and FISH filets. (Pf)
|
10/05/2009 | Routine Inspection |
- Critical: Controlling Pests
- Items:
- Pest(s)
- Problems:
- Present in facility
- Corrections:
- Remove pests from facility.
- Comment:
- Mouse droppings observed on the floor of the dry storage room under the rear shelf units. Pests must be prevented. The person in charge swept and mopped the floor to remove mouse droppings and sugar packets on the floor. A glue board has been placed in the dry storage room to catch mice. Recommend placing peanut butter on center of trap to attract mice to the glue board. This was done in my presence. The violation has been corrected.
- General violation description:
- 6-501.111 - The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the PREMISES by: (A) Routinely inspecting incoming shipments of FOOD and supplies
- Cleaning, Frequency/Restrictio
- Items:
- Physical facilities/structures
- Problems:
- Not clean
- Corrections:
- Keep clean
- Comment:
- Sugar packets and stir sticks on floor of the dry storage room under the shelf racks. Clean the floor regularly to prevent harborage areas for mice to occur. The floor was cleaned to sight and touch in my presence.
- General violation description:
- 6-501.12 - (A) PHYSICAL FACILITIES shall be cleaned as often as necessary to keep them clean. (B) Except for cleaning that is necessary due to a spill or other accident, cleaning shall be done during periods when the least amount of FOOD is exposed such as after closing.
- Good Repair and Proper Adjustm
- Items:
- Equipment
- Problems:
- In poor repair
- Corrections:
- Repair/replace.
- Comment:
- The faucet on the handsink next to the plastic wrap table sprays when the water is running. Repair the nozzle or screen to corect the water from spraying on the table.
- General violation description:
- 4-501.11 - (A) EQUIPMENT shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 and 4-2. (B) EQUIPMENT components such as doors, seals, hinges, fasteners, and kick plates shall be kept intact, tight, and adjusted in accordance with manufacturer's specifications. (C) Cutting or piercing parts of can openers shall be kept sharp to minimize the creation of metal fragments that can contaminate FOOD when the container is opened.
|
10/06/2008 | Routine Inspection |
| No violation noted during this evaluation. | 10/25/2007 | |
Restaurant representatives - add corrected or new information about Thurston High School, 26255 Schoolcraft, See Twp, MI 48239 »