- Critical: Ready-to-Eat, Potentially Haza
- Items:
- In house prepared ready-to-eat potentially hazardous food(s)
- Problems:
- Without date of consumption marking
- Corrections:
- Provide proper date marks as stated above.
- Comment:
- CUT HAM, CHICKEN OBSERVED IN WALK IN COOLER WITHOUT DATE MARKINGS. ALL THESE FOODS SHALL BE DATE MARKED. MARK IMMEDIATELY., , ITEMS MARKED TODAY.
- General violation description:
- 3-501.17 - (A) Except as specified in (E) of this section, refrigerated, READY-TO-EAT, POTENTIALLY HAZARDOUS FOOD prepared and held refrigerated for more than 24 hours in a FOOD ESTABLISHMENT shall be clearly marked at the time of preparation to indicate the date by which the FOOD shall be consumed which is, including the day of preparation: (1) 7 calendar days or less from the day that the FOOD is prepared, if the FOOD is maintained at 5C (41F) or less
- Cleaning, Frequency and Restri
- Items:
- Physical facilities/structures
- Locations:
- Wall(s) dish washing area
- Problems:
- Not clean
- Corrections:
- Keep clean
- General violation description:
- 6-501.12 - (A) PHYSICAL FACILITIES shall be cleaned as often as necessary to keep them clean. (B) Except for cleaning that is necessary due to a spill or other accident, cleaning shall be done during periods when the least amount of FOOD is exposed such as after closing.
- Food Storage
- Items:
- Food item(s) in storage
- Locations:
- walk in freezer(s) floor
- Problems:
- Exposed to dust, splash, or other contaminates
- Corrections:
- Store in protected manner.
- General violation description:
- 3-305.11 - (A) Except as specified in ## (B) and (C) of this section, FOOD shall be protected from contamination by storing the FOOD: (1) In a clean, dry location
|
04/06/2015 | Routine |
- Critical: Packaged and Unpackaged Food -
- Items:
- Raw animal food(s)
- Problems:
- Stored over/next to
- Corrections:
- Store raw animal foods below and away from foods needing little or no further prep.
- Comment:
- Observed a carton of raw shell eggs stored above and next to ready-to-eat foods in the walk-in cooler. Cross-contamination must be avoided. Store eggs below or away from ready-to-eat foods. The shell eggs were placed on the bottom shelf of the walk-in cooler. Violation corrected.
- General violation description:
- 3-302.11 - (A) FOOD shall be protected from cross contamination by: (1) Separating raw animal FOODS during storage, preparation, holding, and display from: (a) Raw READY-TO-EAT FOOD including other raw animal FOOD such as FISH for sushi or MOLLUSCAN SHELLFISH, or other raw READY-TO-EAT FOOD such as vegetables, and (b) Cooked READY-TO-EAT FOOD
- Cleaning, Frequency and Restri
- Items:
- Physical facilities/structures
- Problems:
- Not clean
- Corrections:
- Keep clean
- Comment:
- Observed dusty wall fan in kitchen. Equipment must be kept clean. Clean to sight and touch as needed.
- General violation description:
- 6-501.12 - (A) PHYSICAL FACILITIES shall be cleaned as often as necessary to keep them clean. (B) Except for cleaning that is necessary due to a spill or other accident, cleaning shall be done during periods when the least amount of FOOD is exposed such as after closing.
- Cooking and Baking Equipment
- Items:
- Baking and cooking equipment
- Problems:
- Not cleaned
- Corrections:
- Clean as required above.
- Comment:
- Observed dried food debris inside the kitchen microwave ovens. Cooking equipment must be kept clean. Clean to sight and touch on a daily basis.
- General violation description:
- 4-602.12 - (A) The FOOD-CONTACT SURFACES of cooking and baking EQUIPMENT shall be cleaned at least every 24 hours. This section does not apply to hot oil cooking and filtering EQUIPMENT if it is cleaned as specified in Subparagraph 4-602.11(D)(6). (B) The cavities and door seals of microwave ovens shall be cleaned at least every 24 hours by using the manufacturer's recommended cleaning procedure.
- Good Repair and Proper Adjustm
- Items:
- Equipment
- Problems:
- In poor repair
- Corrections:
- Repair/replace.
- Comment:
- Observed heavy ice build-up on floor of walk-in freezer and moldy caulking behind the dishmachine table. Equipment must be maintained. Defrost the walk-in freezer and replace the moldy caulking.
- General violation description:
- 4-501.11 - (A) EQUIPMENT shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 and 4-2. (B) EQUIPMENT components such as doors, seals, hinges, fasteners, and kick plates shall be kept intact, tight, and adjusted in accordance with manufacturer's specifications. (C) Cutting or piercing parts of can openers shall be kept sharp to minimize the creation of metal fragments that can contaminate FOOD when the container is opened.
- Repairing
- Items:
- Physical facilities
- Problems:
- In poor repair
- Corrections:
- Repair/replace.
- Comment:
- Observed large crack in ceiling above the kitchen stove. Facilities must be maintained. Repair the ceiling to provide a smooth and easily cleanable surface.
- General violation description:
- 6-501.11 - PHYSICAL FACILITIES shall be maintained in good repair.
|
10/27/2014 | Routine |
- Cooking and Baking Equipment
- Items:
- Baking and cooking equipment
- Problems:
- Not cleaned
- Corrections:
- Clean as required above.
- Comment:
- Observed soiled interiors of the microwave ovens. The cooking equipment must be clean. Clean to sight and touch.
- General violation description:
- 4-602.12 - (A) The FOOD-CONTACT SURFACES of cooking and baking EQUIPMENT shall be cleaned at least every 24 hours. This section does not apply to hot oil cooking and filtering EQUIPMENT if it is cleaned as specified in Subparagraph 4-602.11(D)(6). (B) The cavities and door seals of microwave ovens shall be cleaned at least every 24 hours by using the manufacturer's recommended cleaning procedure.
- System Maintained in Good Repa
- Items:
- Plumbing system
- Problems:
- Not maintained
- Corrections:
- Maintain in good repair
- Comment:
- Observed missing drain plugs for the kitchen three compartment sink and drain trap under the bar handsink has a minor leak. Plumbing must be maintained. Replace the missing drain plugs and repair the leaking trap.
- General violation description:
- 5-205.15 - A PLUMBING SYSTEM shall be: (A) Repaired according to LAW
- Ventilation Hood Systems, Adeq
- Items:
- Ventilation hood
- Problems:
- Inadequate
- Corrections:
- Provide adequate ventilation.
- Comment:
- Observed exhaust hood vent blocked for the kitchen dishroom. Ventilation hoods must work adequately. Remove the cover over the vent to provide adequate ventilation.
- General violation description:
- 4-301.14 - Ventilation hood systems and devices shall be sufficient in number and capacity to prevent grease or condensation from collecting on walls and ceilings
|
04/17/2014 | Routine |
- Critical: Temperature Measuring Devices
- Items:
- Thermometer(s)
- Problems:
- Not provided
- Corrections:
- Provide.
- Comment:
- Observed no conspicuous thermometers in the food prep and salad coolers. Conspicuous thermometerrs were provided in my presence. Violation corrected.
- General violation description:
- 4-204.112 - (A) In a mechanically refrigerated or hot FOOD storage unit, the sensor of a TEMPERATURE MEASURING DEVICE shall be located to measure the air temperature or a simulated product temperature in the warmest part of a mechanically refrigerated unit and in the coolest part of a hot FOOD storage unit. (B) Except as specified in # (C) of this section, cold or hot holding EQUIPMENT used for POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be designed to include and shall be equipped with at least one integral or permanently affixed TEMPERATURE MEASURING DEVICE that is located to allow easy viewing of the device's temperature display. (C) Paragraph (B) of this section does not apply to EQUIPMENT for which the placement of a TEMPERATURE MEASURNG DEVICE is not a practical means for measuring the ambient air surrounding the FOOD because of the design, type, and use of the EQUIPMENT, such as calrod units, heat lamps, cold plates, bainmaries, steam tables, insulated FOOD transport containers, and salad bars. (D) TEMPERATURE MEASURING DEVICES shall be designed to be easily readable. (E) FOOD TEMPERATURE MEASURING DEVICES and water TEMPERATURE MEASURING DEVICES on WAREWASHING machines shall have a numerical scale, printed record, or digital readout in increments no greater than 1°C or 2°F in the intended range of use.(Pf)
- Good Repair and Proper Adjustm
- Items:
- Equipment
- Problems:
- In poor repair
- Corrections:
- Repair/replace.
- Comment:
- Observed minor leak coming from the drain trap for the bar handsink. Equipment must be maintained. Repair the drain trap to eliminate the water leak.
- General violation description:
- 4-501.11 - (A) EQUIPMENT shall be maintained in a state of repair and condition that meets the requirements specified under Parts 4-1 and 4-2. (B) EQUIPMENT components such as doors, seals, hinges, fasteners, and kick plates shall be kept intact, tight, and adjusted in accordance with manufacturer's specifications. (C) Cutting or piercing parts of can openers shall be kept sharp to minimize the creation of metal fragments that can contaminate FOOD when the container is opened.
- Nonfood-Contact Surfaces
- Items:
- Nonfood contact surface(s)
- Problems:
- Soiled
- Corrections:
- Keep clean.
- Comment:
- Observed dusty condenser in the walk-in cooler and mold on walls of walk-in cooler. Non- food contact surfaces must be kept clean. Clean to sight and touch as needed.
- General violation description:
- 4-602.13 - NonFOOD-CONTACT SURFACES of EQUIPMENT shall be cleaned at a frequency necessary to preclude accumulation of soil residues.
|
10/23/2013 | Routine |
| No violation noted during this evaluation. | 10/24/2012 | Routine Inspection |
- Critical: Clean Sight/Touch-No Accum/Enc
- Comment:
- THE ICE MAKER WAS CLEANED, WASHED, RINSED AND SANITIZED. VIOLATION HAD BEEN CORRECTED.
- General violation description:
- 4-601.11 - (A) EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be clean to sight and touch. (B) The FOOD-CONTACT SURFACES of cooking EQUIPMENT and pans shall be kept free of encrusted grease deposits and other soil accumulations. N (C) NonFOOD-CONTACT SURFACES of EQUIPMENT shall be kept free of an accumulation of dust, dirt, FOOD residue, and other debris. N
|
04/17/2012 | Follow-up |
- Critical: Clean Sight/Touch-No Accum/Enc
- Items:
- Food-contact surface(s)
- Problems:
- Soiled
- Corrections:
- Keep clean.
- Comment:
- Mold is growing inside the ice maker. Empty the ice maker, wash, rinse and sanitize all the inside walls. A follow up inspection will be conducted with in 10 days.,
- General violation description:
- 4-601.11 - (A) EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be clean to sight and touch. (B) The FOOD-CONTACT SURFACES of cooking EQUIPMENT and pans shall be kept free of encrusted grease deposits and other soil accumulations. N (C) NonFOOD-CONTACT SURFACES of EQUIPMENT shall be kept free of an accumulation of dust, dirt, FOOD residue, and other debris. N
- Clean Freq, Nonfood-Contact Su
- Items:
- Nonfood contact surface(s)
- Problems:
- With accumulation of debris
- Corrections:
- Keep clean.
- Comment:
- Mold is growing on the side wall where the dish washer was located. Clean and sanitize.
- General violation description:
- 4-602.13 - NonFOOD-CONTACT SURFACES of EQUIPMENT shall be cleaned at a frequency necessary to preclude accumulation of soil residues.
|
04/11/2012 | Routine Inspection |
- Critical: Methods-Hot Water and Chemical
- Comment:
- THE HIGH TEMP SWITCH WAS REPLACED. THE THERMO STRIP TURNED BLACK. VIOLATION HAD BEEN CORRECTED.
- General violation description:
- 4-703.11 - After being cleaned, EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be SANITIZED in: (A) Hot water manual operations by immersion for at least 30 seconds and as specified under 4-501.111
|
11/04/2011 | Follow-up |
- Critical: Methods-Hot Water and Chemical
- Items:
- Hot water sanitizer
- Problems:
- Does not allow surface temperature to reach 160 degrees f
- Corrections:
- Provide 170 degree F hot water for sanitizing.
- Comment:
- THE HOT WATER SANITIZING DISH WASHER DID NOT CHANGE THE COLOR OF THE THERMO TEST STRIP. A FOLLOW UP INSPECTION WILL BE CONDUCTED WITH IN 10 DAYS. MEAN TIME SANITIZE THE DISHES IN THE 3 COMPARTMENT SINK. ,
- General violation description:
- 4-703.11 - After being cleaned, EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be SANITIZED in: (A) Hot water manual operations by immersion for at least 30 seconds and as specified under 4-501.111
|
10/19/2011 | Routine Inspection |
- Critical: Backflow prevention
- Comment:
- AIR GAP WAS PROVIDED FOR THE 3 COMPARTMENT SINK DRAIN PIPE. VIOLATION HAD BEEN CORRECTED.
- General violation description:
- 5-402.11 - (A) Except as specified in (B) and (C) of this section, a direct connection may not exist between the SEWAGE system and a drain originating from EQUIPMENT in which FOOD, portable EQUIPMENT, or UTENSILS are placed. (B) If allowed by LAW, a WAREWASHING machine may have a direct connection between its waste outlet and a floor drain when the machine is located within 1.5 m (5 feet) of a trapped floor drain and the machine outlet is connected to the inlet side of a properly vented floor drain trap. (C) If allowed by LAW, a WAREWASHING or culinary sink may have a direct connection.
|
05/12/2011 | Follow-up |
| No violation noted during this evaluation. | 04/29/2011 | Follow-up |
- Critical: Backflow prevention
- Items:
- Backflow/backsiphonage prevention device(s) Air gap
- Problems:
- Not provided on Sink
- Corrections:
- Provide adequate air gap.
- Comment:
- THE 3 COMPARTMENT SINK DRAIN PIPE IS INSIDE THE SEWER DRAIN. THE GLASSWARE IS WASHED IN THIS 3 COMPARTMENT SINK. PROVIDE A MINIMUM OF AN 1 INCH AIR GAP BETWEEN THE BOTTOM OF THE EQUIPMENT DRAIN AND THE TOP OF THE SEWER DRAIN. A FOLLOW UP INSPECTION WILL BE CONDUCTED WITH IN 10 DAYS.
- General violation description:
- 5-402.11 - (A) Except as specified in (B) and (C) of this section, a direct connection may not exist between the SEWAGE system and a drain originating from EQUIPMENT in which FOOD, portable EQUIPMENT, or UTENSILS are placed. (B) If allowed by LAW, a WAREWASHING machine may have a direct connection between its waste outlet and a floor drain when the machine is located within 1.5 m (5 feet) of a trapped floor drain and the machine outlet is connected to the inlet side of a properly vented floor drain trap. (C) If allowed by LAW, a WAREWASHING or culinary sink may have a direct connection.
- Critical: Backflow prevention
- Items:
- Backflow/backsiphonage prevention device(s) Air gap
- Problems:
- Not provided on Sink
- Corrections:
- Provide adequate air gap.
- Comment:
- THE 3 COMPARTMENT SINK DRAIN PIPE IS INSIDE THE SEWER DRAIN. THE GLASSWARE IS WASHED IN THIS 3 COMPARTMENT SINK. PROVIDE A MINIMUM OF AN 1 INCH AIR GAP BETWEEN THE BOTTOM OF THE EQUIPMENT DRAIN AND THE TOP OF THE SEWER DRAIN. A FOLLOW UP INSPECTION WILL BE CONDUCTED WITH IN 10 DAYS., ,
- General violation description:
- 5-402.11 - (A) Except as specified in (B) and (C) of this section, a direct connection may not exist between the SEWAGE system and a drain originating from EQUIPMENT in which FOOD, portable EQUIPMENT, or UTENSILS are placed. (B) If allowed by LAW, a WAREWASHING machine may have a direct connection between its waste outlet and a floor drain when the machine is located within 1.5 m (5 feet) of a trapped floor drain and the machine outlet is connected to the inlet side of a properly vented floor drain trap. (C) If allowed by LAW, a WAREWASHING or culinary sink may have a direct connection.
- Critical: Methods-Hot Water and Chemical
- Items:
- Hot water sanitizer
- Problems:
- Does not allow surface temperature to reach 160 degrees f
- Corrections:
- Provide 170 degree F hot water for sanitizing.
- Comment:
- THE HOT WATER MACHINE DID NOT REACH THE SANITIZATION TEMPERATURE OF 160F. MEAN TIME SANITIZE THE DISHES IN THE THREE COMPARTMENT SINK. A FOLLOW UP INSPECTION WILL BE CONDUCTED WITH IN 10 DAYS.
- General violation description:
- 4-703.11 - After being cleaned, EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be SANITIZED in: (A) Hot water manual operations by immersion for at least 30 seconds and as specified under 4-501.111
- Critical: Methods-Hot Water and Chemical
- Items:
- Hot water sanitizer
- Problems:
- Does not allow surface temperature to reach 160 degrees f
- Corrections:
- Provide 170 degree F hot water for sanitizing.
- Comment:
- THE HOT WATER MACHINE DID NOT REACH THE SANITIZATION TEMPERATURE OF 160F. MEAN TIME SANITIZE THE DISHES IN THE THREE COMPARTMENT SINK. A FOLLOW UP INSPECTION WILL BE CONDUCTED WITH IN 10 DAYS.,
- General violation description:
- 4-703.11 - After being cleaned, EQUIPMENT FOOD-CONTACT SURFACES and UTENSILS shall be SANITIZED in: (A) Hot water manual operations by immersion for at least 30 seconds and as specified under 4-501.111
|
04/26/2011 | Routine Inspection |
- Critical: Backflow Prevention Device/Req
- Comment:
- CORRECTION MADE
- General violation description:
- 5-203.14 - OBSERVED A NEWLY INSTALLED 100 MESH IN LINE WATER FILTER FOLLOWED BY A 1022 VENTED BACK FLOW DEVICE LOCATED DOWN STREAM OF THE COPPER PIPE WATER FEED LINE TO THE CARBONATOR.
- Repairing
- Comment:
- CORRECTION MADE: OBSERVED NEWLY INSTALLED TILE FLOORING IN THE WALK-IN COOLER.
- General violation description:
- 6-501.11 - PHYSICAL FACILITIES shall be maintained in good repair.
|
11/12/2010 | Follow-up |
Restaurant representatives - add corrected or new information about Wagon Wheel Lounge, 212 Main, Northville, MI 48167 »