- Critical: Manual and Mechanical Warewash
- Comment:
- Corrected Chlorine is properly dispensed into the machine at 100ppm.
- General violation description:
- 4-501.114 - A chemical SANITIZER used in a SANITIZING solution for a manual or mechanical operation at exposure times specified under 4-703.11(C) shall be listed in 21 CFR 178.1010 Sanitizing solutions, shall be used in accordance with the EPA-approved manufacturer's label use instructions, and shall be used as follows: (A) A chlorine solution shall have a minimum temperature based on the concentration and pH of the solution as listed in the following chart
- Critical: Warewashing Equipment, Determi
- Comment:
- Corrected Chlorine test strips are readily available.
- General violation description:
- 4-501.116 - Concentration of the SANITIZING solution shall be accurately determined by using a test kit or other device.(Pf)
|
06/18/2015 | Follow-up |
- Critical: Manual and Mechanical Warewash
- Items:
- Chlorine solution concentration
- Problems:
- Below 25 ppm
- Corrections:
- Provide correct concentration as stated above.
- Comment:
- A chlorine sanitizer concentration must be between 50 to 100ppm. The chlorine sanitizer is not properly dispensing into the dishmachine. Repair so chlorine is properly dispensing into the warewashing unit. ,
- General violation description:
- 4-501.114 - A chemical SANITIZER used in a SANITIZING solution for a manual or mechanical operation at exposure times specified under 4-703.11(C) shall be listed in 21 CFR 178.1010 Sanitizing solutions, shall be used in accordance with the EPA-approved manufacturer's label use instructions, and shall be used as follows: (A) A chlorine solution shall have a minimum temperature based on the concentration and pH of the solution as listed in the following chart
- Critical: Ready-to-Eat, Potentially Haza
- Items:
- In house prepared ready-to-eat potentially hazardous food(s)
- Problems:
- Improperly date marked
- Comment:
- Food held beyond the 7-day period must be discarded. Observed roasted red pepper in the cookline prep cooler that had mold on them. There was a container of rice in the prep cooler that was beyond the 7 day period (5/15/15). Food was discarded during inspection.
- General violation description:
- 3-501.17 - (A) Except as specified in (E) of this section, refrigerated, READY-TO-EAT, POTENTIALLY HAZARDOUS FOOD prepared and held refrigerated for more than 24 hours in a FOOD ESTABLISHMENT shall be clearly marked at the time of preparation to indicate the date by which the FOOD shall be consumed which is, including the day of preparation: (1) 7 calendar days or less from the day that the FOOD is prepared, if the FOOD is maintained at 5C (41F) or less
- Critical: Warewashing Equipment, Determi
- Items:
- Sanitizer test kit
- Problems:
- Not used
- Corrections:
- Use test kit to verify sanitizer concentration.
- Comment:
- Concentration of sanitizing solution must be determined by the proper test kit. There was no chlorine test kit available. Provide chlorine test kit to accurately test concentration of sanitizer in the dishmachine.,
- General violation description:
- 4-501.116 - Concentration of the SANITIZING solution shall be accurately determined by using a test kit or other device.(Pf)
- Temperature Measuring Devices
- Items:
- Thermometer(s) refrigeration
- Problems:
- Not provided
- Corrections:
- Provide.
- Comment:
- A temperature measuring device must be provided for cold holding equipment that holds potentially hazardous food. Observed no thermometer inside the prep cooler on the cookline. Provide conspicuous thermometer inside unit.
- General violation description:
- 4-204.112 - (A) In a mechanically refrigerated or hot FOOD storage unit, the sensor of a TEMPERATURE MEASURING DEVICE shall be located to measure the air temperature or a simulated product temperature in the warmest part of a mechanically refrigerated unit and in the coolest part of a hot FOOD storage unit. (B) Except as specified in # (C) of this section, cold or hot holding EQUIPMENT used for POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be designed to include and shall be equipped with at least one integral or permanently affixed TEMPERATURE MEASURING DEVICE that is located to allow easy viewing of the device's temperature display. (C) Paragraph (B) of this section does not apply to EQUIPMENT for which the placement of a TEMPERATURE MEASURNG DEVICE is not a practical means for measuring the ambient air surrounding the FOOD because of the design, type, and use of the EQUIPMENT, such as calrod units, heat lamps, cold plates, bainmaries, steam tables, insulated FOOD transport containers, and salad bars. (D) TEMPERATURE MEASURING DEVICES shall be designed to be easily readable. (E) FOOD TEMPERATURE MEASURING DEVICES and water TEMPERATURE MEASURING DEVICES on WAREWASHING machines shall have a numerical scale, printed record, or digital readout in increments no greater than 1°C or 2°F in the intended range of use.(Pf)
|
05/26/2015 | Routine |
- Critical: Using a Handwashing Sink
- Comment:
- Observed at time of inspection hand wash sink is no longer blocked by roll stamp. Corrected.
- General violation description:
- 5-205.11 - (A) A HANDWASHING SINK shall be maintained so that it is accessible at all times for EMPLOYEE use. (Pf) (B) A HANDWASHING SINK may not be used for purposes other than handwashing. (Pf) (C) An automatic handwashing facility shall be used in accordance with manufacturer's instructions. (Pf)
|
11/21/2014 | Follow-up |
- Critical: Using a Handwashing Sink
- Items:
- Handwashing sink(s)
- Problems:
- Not easily accessible
- Corrections:
- Make easily accessible.
- Comment:
- Observed at time of inspection hand wash sink in kitchen by prep line blocked by speed rack and hand wash sink in man prep area blocked by roll stampers. Speed rack was moved at time of inspection but other machine roll stampers is too big to move at time of inspection. Correct by moving roll stamper so that it is no longer blocking the hand wash sink. Correct immediately a follow up will occur in about 10 day.,
- General violation description:
- 5-205.11 - (A) A HANDWASHING SINK shall be maintained so that it is accessible at all times for EMPLOYEE use. (Pf) (B) A HANDWASHING SINK may not be used for purposes other than handwashing. (Pf) (C) An automatic handwashing facility shall be used in accordance with manufacturer's instructions. (Pf)
- Food Storage
- Items:
- Food item(s) in storage
- Problems:
- Stored on floor or less than 6 inches above floor
- Corrections:
- Store at least 6 inches above the floor.
- Comment:
- Observed at time of inspection bags of dry storage food (flour, sugar, salt) stored on the floor. Correct by storing at least 6 in up off the ground. Correct as soon as possible a follow up will occur at the next routine inspection.
- General violation description:
- 3-305.11 - (A) Except as specified in ## (B) and (C) of this section, FOOD shall be protected from contamination by storing the FOOD: (1) In a clean, dry location
- Wiping Cloths, Use Limitation
- Items:
- Wiping cloth(s)
- Problems:
- Not completely submerged in sanitizing solution
- Corrections:
- Store wiping cloths completely submersed in sanitizer.
- Comment:
- Observed at time of inspection wet sanitizer cloths stored on counter tops. Correct by storing sanitizer cloths completely submerged in sanitizer solution to prevent the growth and of pathogens. Correct immediately a follow up will occur at the next routine inspection.
- General violation description:
- 3-304.14 - (A) Cloths in-use for wiping food spills from TABLEWARE and carry-out containers that occur as FOOD is being served shall be: (1) Maintained dry
|
11/11/2014 | Routine |
- Critical: Backflow Prevention
- Comment:
- CORRECTED BY PROVIDING AT LEAST A 1 INCH AIR GAP BETWEEN DRIAN LINE AND DRAIN BOWL.
- General violation description:
- 5-402.11 - (A) Except as specified in (B) and (C) of this section, a direct connection may not exist between the SEWAGE system and a drain originating from EQUIPMENT in which FOOD, portable EQUIPMENT, or UTENSILS are placed. (B) If allowed by LAW, a WAREWASHING machine may have a direct connection between its waste outlet and a floor drain when the machine is located within 1.5 m (5 feet) of a trapped floor drain and the machine outlet is connected to the inlet side of a properly vented floor drain trap. (C) If allowed by LAW, a WAREWASHING or culinary sink may have a direct connection.
- Critical: Temperature Measuring Devices
- Comment:
- CORRECTED BY PROVIDING THERMOMETERS IN ALL COOLERS.
- General violation description:
- 4-204.112 - (A) In a mechanically refrigerated or hot FOOD storage unit, the sensor of a TEMPERATURE MEASURING DEVICE shall be located to measure the air temperature or a simulated product temperature in the warmest part of a mechanically refrigerated unit and in the coolest part of a hot FOOD storage unit. (B) Except as specified in # (C) of this section, cold or hot holding EQUIPMENT used for POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be designed to include and shall be equipped with at least one integral or permanently affixed TEMPERATURE MEASURING DEVICE that is located to allow easy viewing of the device's temperature display. (C) Paragraph (B) of this section does not apply to EQUIPMENT for which the placement of a TEMPERATURE MEASURNG DEVICE is not a practical means for measuring the ambient air surrounding the FOOD because of the design, type, and use of the EQUIPMENT, such as calrod units, heat lamps, cold plates, bainmaries, steam tables, insulated FOOD transport containers, and salad bars. (D) TEMPERATURE MEASURING DEVICES shall be designed to be easily readable. (E) FOOD TEMPERATURE MEASURING DEVICES and water TEMPERATURE MEASURING DEVICES on WAREWASHING machines shall have a numerical scale, printed record, or digital readout in increments no greater than 1°C or 2°F in the intended range of use.(Pf)
|
09/23/2014 | Follow-up |
- Critical: Backflow Prevention
- Comment:
- CORRECTED BY PROVIDING AT LEAST A 1 INCH AIR GAP BETWEEN DRIAN LINE AND DRAIN BOWL.
- General violation description:
- 5-402.11 - (A) Except as specified in (B) and (C) of this section, a direct connection may not exist between the SEWAGE system and a drain originating from EQUIPMENT in which FOOD, portable EQUIPMENT, or UTENSILS are placed. (B) If allowed by LAW, a WAREWASHING machine may have a direct connection between its waste outlet and a floor drain when the machine is located within 1.5 m (5 feet) of a trapped floor drain and the machine outlet is connected to the inlet side of a properly vented floor drain trap. (C) If allowed by LAW, a WAREWASHING or culinary sink may have a direct connection.
- Critical: Temperature Measuring Devices
- Comment:
- CORRECTED BY PROVIDING THERMOMETERS IN ALL COOLERS.
- General violation description:
- 4-204.112 - (A) In a mechanically refrigerated or hot FOOD storage unit, the sensor of a TEMPERATURE MEASURING DEVICE shall be located to measure the air temperature or a simulated product temperature in the warmest part of a mechanically refrigerated unit and in the coolest part of a hot FOOD storage unit. (B) Except as specified in # (C) of this section, cold or hot holding EQUIPMENT used for POTENTIALLY HAZARDOUS FOOD (TIME/TEMPERATURE CONTROL FOR SAFETY FOOD) shall be designed to include and shall be equipped with at least one integral or permanently affixed TEMPERATURE MEASURING DEVICE that is located to allow easy viewing of the device's temperature display. (C) Paragraph (B) of this section does not apply to EQUIPMENT for which the placement of a TEMPERATURE MEASURNG DEVICE is not a practical means for measuring the ambient air surrounding the FOOD because of the design, type, and use of the EQUIPMENT, such as calrod units, heat lamps, cold plates, bainmaries, steam tables, insulated FOOD transport containers, and salad bars. (D) TEMPERATURE MEASURING DEVICES shall be designed to be easily readable. (E) FOOD TEMPERATURE MEASURING DEVICES and water TEMPERATURE MEASURING DEVICES on WAREWASHING machines shall have a numerical scale, printed record, or digital readout in increments no greater than 1°C or 2°F in the intended range of use.(Pf)
|
09/23/2014 | Follow-up |
Restaurant representatives - add corrected or new information about Gunnell Baked Goods Llc(Cornwall Bakery), 15215 Kercheval Ave, Grosse Pointe Park, MI 48230 »